(Ref. Fig. 509A/TASK 27-41-00-991-011-A)
Rear THS Control Cables Length Adjustment
Figure 509/TASK 27-41-00-991-011
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-41-00Page 547 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
R Rear THS Control Cables Length Adjustment
R Figure 509A/TASK 27-41-00-991-011-A
1EFF : 301-399, 1 27-41-00 Page 548
1 1 May 01/04
1 1
1CES 1
**ON A/C ALL
Subtask 27-41-00-820-055
A. Pre-tension of the Cables
(1) You must put a pre-tension on the cable before you adjust it.
-In theory, the pre-tension time is 48 hours without movement of the aircraft. After this pre-tension time, the adjustment of the cable will stay correct.
-A minimum pre-tension time of 4 hours without movement of the aircraft is permitted. The adjustment of the cable will not stay correct for a long time. You must do the full pre-tension procedure when the aircraft stops for maintenance for a sufficiently long time.
NOTE : For a pre-tension time between 4 and 48 hours, the stability
____ of the adjustments is in proportion to the pre-tension time.
(2)
Apply a tension of 55 daN (123.6448 lbf) plus or minus 5 daN (11.2404 lbf) to the cable linkage.
(3)
The linkage must stay in this position for 48 hours.
Subtask 27-41-00-220-063
B. Measurement
(1) Measure the cable zone temperature and the external temperature with a thermometer. Make sure that the temperature is the same at plus or minus 2 DEG.C (plus or minus 3.60 DEG.F).
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 27-41-00-820-056
C. Cutting of the Rear Control Cable of the THS
(1) Measure the distance between FR35 and the rear control cable of the THS. Make a mark on each cable:
-for the right cable: at 542.9 mm (21.3740 in.) plus or minus 2 mm (0.0787 in.)
- for the left cable: at 2542.9 mm (100.1142 in.) plus or minus 2 mm
(0.0787 in.)
(2) Release the tension on the cables.
(3) Cut the cables at the marks you did before.
(4) Install the terminal studs on the cable ends (Ref. CFM Cable
Fabrication Man).
R **ON A/C 301-399,
R Subtask 27-41-00-820-056-A
R C. Cutting of the Rear Control Cable of the THS
R (1) Measure the distance between FR35.3 and the rear control cable of the
R THS.
R Make a mark on each cable:
R - for the right cable: at 564.9 mm (22.2401 in.) plus or minus 2 mm
R (0.0787 in.)
R - for the left cable: at 2675.3 mm (105.3268 in.) plus or minus 2 mm
R (0.0787 in.)
R (2) Release the tension on the cables.
R (3) Cut the cables at the marks you did before.
R (4) Install the terminal studs on the cable ends (Ref. CFM Cable
R Fabrication Man).
THS MECHANICAL CONTROL - INSPECTION/CHECK
_________________________________________
TASK 27-41-00-210-001
R Detailed Visual Inspection of the THS Mechanical Control
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 274100-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
R No specific 1 ACCESS PLATFORM 2M (6 FT)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
20-24-11-100-001 Cleaning and Protection of the Cables 20-24-12-200-001 Check of the Control Cables 25-54-12-000-001 Removal of the FWD Cargo Compartment Partition FR34 25-54-12-000-002 Removal of the Ceiling Panels in the FWD Cargo
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱3(93)
