R R (d) Install the plate (37) with the washers (32), (36) the nuts (33) and the bolts (35).
R (e) Safety the bolt (25) with a new cotter pin (24)
R (7) If the servo control is going to be secure by ABS
R (a) Install the washer (41).
R R (b) Torque the nut (38) to between 4.5 and 5.0 m.daN (33.18 and 36.87 lbf.ft). Install the locking cup (39) and the cotter pin (40).
R R (c) Install the plate (37) with the washers (32), (36) the nuts (33) and the bolts (35).
R R (8) Apply SPECIAL MATERIALS (Material No. 05-005) to all the remaining unprotected steel attachment parts of the elevator servo control.
R R NOTE : Do not allow SPECIAL MATERIALS (Material No. 05-005) to get on____ the servo control spherical bearing .
R **ON A/C 001-003, 052-054,
Subtask 27-34-51-420-065
B. Installation of the Servovontrol Unit to the Elevator attachment. (Ref. Fig. 401/TASK 27-34-51-991-001, 402/TASK 27-34-51-991-010)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Apply COMMON GREASE (Material No. 04-004) to the outer surface of the bush (26) and install it.
(2) Apply SPECIAL MATERIALS (Material No. 05-002) to the head and shank of the bolt (27).
(3) Put the servocontrol unit (4) in position and support it.
R 1EFF : 001-003, 051-054, 1 27-34-51Page 425 1 1 May 01/05 1 1 1CES 1
(4)
Install the bolt (27).
(5)
Apply COMMON GREASE (Material No. 04-004) to the thread of the bolt (27).
(6)
Install the cup washer (24), the spacer (23) and the nut (22).
(7)
Torque the nut (22) to between 4.5 and 5.0 m.daN (33.18 and 36.87 lbf.ft).
(8)
Install the locking cup (21), and the cotter pin (20) and cotter pin (25).
(9)
Apply SPECIAL MATERIALS (Material No. 05-005) to all the remaining unprotected steel attachment parts of the elevator servocontrol.
NOTE : Do not allow SPECIAL MATERIALS (Material No. 05-005) to get on
____
the servocontrol spherical bearing .
R **ON A/C 004-049, 055-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 27-34-51-420-065-A
B. Installation of the Servocontrol Unit to the Elevator attachment. (Ref. Fig. 401/TASK 27-34-51-991-001, 402A/TASK 27-34-51-991-010-A)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1)
Apply COMMON GREASE (Material No. 04-004) to the outer surface of the bush (26) and install it.
(2)
Apply SPECIAL MATERIALS (Material No. 05-002) to the head and shank of the bolt (27).
(3)
Put the servocontrol unit (4) in position and support it.
(4)
Install the bolt (27).
R 1EFF : 001-049, 052-099, 101-149, 151-199, 1 27-34-51Page 426 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(5)
Apply COMMON GREASE (Material No. 04-004) to the thread of the bolt (27).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱3(63)
