Subtask 27-50-00-865-054
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 R 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
Subtask 27-50-00-865-055
D. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/WTB/FLP/SYS2 12CV P20 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21 122VU FLIGHT CONTROLS/WTB/FLP/SYS1 10CV S07
4. Procedure
_________
Subtask 27-50-00-866-052
A. Extension of the Flaps on the Ground WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Do the EIS start procedure (Ref. TASK 31-60-00-860-001).
(2)
Set the flap/slat control lever to position 1, 2, 3 or FULL.
(3)
Make sure that on the upper display unit of the ECAM system the flap position bar moves to the set position.
(4)
Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) (Ref. TASK 27-00-00-480-002) on the flap/slat control lever.
5. Close-up
________ Subtask 27-50-00-860-055
A. Aircraft Configuration
(1)
Depressurize the Yellow hydraulic system
(Ref. TASK 29-10-00-864-002).
(2)
Do the EIS stop procedure (Ref. TASK 31-60-00-860-002).
(3)
De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
Subtask 27-50-00-942-055
B. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-50-00Page 204 1 1 May 01/04R 1 1 1CES 1
TASK 27-50-00-866-008- 01
Extension of the Flaps/Slats on the Ground
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : IF THE THRUST REVERSER COWLS ARE OPEN, MAKE SURE THAT THE HALF DOORS
_______ OF THE THRUST REVERSER ARE RETRACTED BEFORE YOU EXTEND THE SLATS. IF THE DOORS ARE EXTENDED, YOU CAN CAUSE DAMAGE TO THE SLATS AND HALF DOORS WHEN THE SLATS EXTEND.
1. Reason for the Job
__________________
To extend the flaps and slats at the same time.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notice(s) 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVERR B. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R 24-41-00-861-002 R R 24-41-00-862-002 R R 27-00-00-480-002 R R 29-10-00-863-002 R 29-10-00-863-003 R R 29-10-00-864-002 R 29-10-00-864-003 R 29-23-00-860-001 R R 29-23-00-860-002 R R 31-60-00-860-001 R 31-60-00-860-002
R 3. Job Set-up
__________
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱3(190)
