-------------------------------------------------------------------------------
| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | C | 12.675 | 12.687 | | | 12.662 | | | | OD 8 |(0.4990) |(0.4994) | | |(0.4985) | | | | | | | 0.000 | 0.025 | | | 0.051 | | | | | (0.0000)| (0.0009)| | |(0.0020)| | C | 12.687 | 12.700 | | | | 12.713 | | | ID 4 |(0.4994) |(0.5000) | | | |(0.5005) | | -------------------------------------------------------------------------------
Subtask 27-34-41-220-054
F. Fits and Clearances
(1) Complete an inspection of these dimensions,
-------------------------------------------------------------------------------
| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | C | 9.500 | 9.512 | | | 9.487 | | | | OD 6 |(0.3740) |(0.3744) | | |(0.3735) | | | | | | | 0.000 | 0.025 | | | 0.051 | | | | | (0.0000)| (0.0009)| | |(0.0020)| | C | 9.512 | 9.525 | | | | 9.538 | | | ID 8 |(0.3744) |(0.3750) | | | |(0.3755) | | -------------------------------------------------------------------------------
R Subtask 27-34-41-020-055
R G. Replacement of Unserviceable Items
R (1) For removal of the plain bushes a dimensional check is not necessary.
R R (2) If the plain-bushes internal diameter are out of limits see the CMM replacement procedure (Ref. CMM 552115PB601).
R R (3) If you find unserviceable bolts or plain bushes replace them with new parts.
5. Close-up________
Subtask 27-34-41-410-051
A. Close Access
(1) Install the elevator (Ref. TASK 27-34-41-400-001)
Subtask 27-34-41-942-051
B. Removal of Equipment
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
FILTER - HYDRAULIC - SERVICING
______________________________
TASK 27-34-42-600-001
Servicing of the Elevator Servo Control Actuator Filter
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______ CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : MAKE SURE THAT THE CONTROLS AGREE WITH THE POSITION OF THE ITEMS THEY
_______ OPERATE BEFORE YOU PRESSURIZE A HYDRAULIC SYSTEM.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______ FALL CAN INJURE OR KILL YOU.
1. Reason for the Job__________________ Self Explanatory
2. Job Set-up Information______________________
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱3(55)
