(f)
Turn the actuator housing (13) until:
-the 'R' on the actuator housing aligns with the arrow on the offset gearbox (16).
(g) Application of special material:
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER
_______ SPECIAL MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
Apply a layer of SPECIAL MATERIALS (Material No. 05-115) to the shanks of the bolts (14).
(h)
Install the bolts (14) and the washers (15). TORQUE the bolts
(14)
to between 0.78 and 0.96 m.daN (69.02 and 84.95 lbf.in).
(i)
Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to:
-
the bolts (6), washers (7) and nuts (8)
-
the heads of the bolts (14) and the washers (15).
(2) Make sure that the actuator housing (13), the offset gearbox (16) and the torque limiter assembly (5) are aligned.
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-54-49Page A421 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-061, 101-105, 201-203,
Subtask 27-54-49-420-084
B. General
(1)
The flap actuator has an off-set gearbox and a rotary actuator. The rotary actuator is a vented unit filled with grease.
(2)
It is normal for this grease to have some oil separation. The external surfaces of the rotary actuator may be moist with this separated oil as it is not a hermetically sealed unit. However, separated oil in the unit that touches the grease will be changed back during operation. The oil separation will decrease during in-service operation until the lubricant is in a condition that is stable. This is normal and will not cause damage to the unit.
**ON A/C ALL
Subtask 27-54-49-420-062
C. Preparation for Installation
CAUTION : DO NOT APPLY MORE THAN ONE TYPE OF LUBRICANT.
_______
GREASE AND ASSEMBLY PASTE DO NOT MIX.
(1)
Clean the component interfaces and the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(2)
Clean these items with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026):
-
the internal splines of the flap drive lever
-
the drive splines of the flap actuator
-
the internal splines of the torque limiter
-
the splines of the universal joint (1).
(3)
Do a visual check for the correct condition of:
-
the internal splines of the flap drive lever
-
the drive splines of the flap actuator
-
the internal splines of the torque limiter
-
the splines of the universal joint (1).
(4)
Do an inspection of the component interface and/or the adjacent area.
(5)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(6)
Do one of the steps that follow:
CAUTION : DO NOT APPLY MORE THAN ONE TYPE OF LUBRICANT.
_______ GREASE AND ASSEMBLY PASTE DO NOT MIX.
(a) Apply a thin layer of COMMON GREASE (Material No. 04-024) to:
-
the drive splines of the actuator
-
the internal splines of the flap drive lever
-
the internal splines of the torque limiter.
- or
(b) Apply a thin layer of COMMON GREASE (Material No. 04-018) to:
-
the drive splines of the actuator
-
the internal splines of the flap drive lever
-
the internal splines of the torque limiter.
R **ON A/C 001-049, 051-061, 101-105, 201-203,
Subtask 27-54-49-420-066
D. Installation of the Flap Track 4 Actuator 6233CM(6283CM)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
CAUTION : SUPPORT THE ACTUATOR, WHICH CAN WEIGH UP TO 10.5kg (23.2lbs).
_______ THIS WILL PREVENT DAMAGE TO THE RELATED STRUCTURE AND EQUIPMENT.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱5(130)
