(b)
Remove the hinge pin (96) sufficiently to let you connect the tab drive control-rod (97). Do not fully remove the hinge pin (96).
NOTE : If you fully remove the hinge pin (96) from the carriage
____ (94), the roller bearing block (95) will fall out of alignment.
(c)
Install the loose bush (98).
(d)
Connect the tab drive control-rod (97) to the track 4 carriage with the hinge pin (96).
(e)
Install the washer (99) and the nut (100).
(f)
TORQUE the nut (100) to between 1.4 and 2.7 m.daN (10.32 and
19.91 lbf.ft).
(g) Safety the nut (100) with the new cotter pin (101).
(7) If applicable, install the Z-coupling: R (Ref. Fig. 607/TASK 27-54-00-991-017)
(a)
Retract the flaps to position 1 (Ref. TASK 27-50-00-866-009).
(b)
Remove the Z-coupling lever (4) from the inboard flap attachment-bracket (5):
1 Remove the nut (2), the washer (3), the bolt (10) and the
_
lever (4).
2 Remove the nut (7), the washer (8) and the spacer(s) (9).
_
(c)
Retract the flaps fully (Ref. TASK 27-50-00-866-009).
(d)
Install the lever (4) with the same number of spacers (9) you removed between the levers (4) and (5).
(e)
Install the bolt (10).
(f)
Extend the flaps to the position 1 (Ref. TASK 27-50-00-866-009).
R 1EFF : 301-399, 1 27-54-00Page A607 1 1 May 01/05 1 1 1CES 1
(g)
Install the washer (3) and the nut (2).
(h)
TORQUE the nut (2) to between 0.9 and 1 m.daN (79.64 and 88.49 lbf.in).
(i)
Safety the nut (2) with a new cotter pin (1).
(j)
Retract the flaps to the O position (Ref. TASK 27-50-00-866-009).
(k)
Install the remaining spacer(s) (9), the washer (8) and the nut (7).
(l)
TORQUE the nut (7) to between 3.1 and 3.6 m.daN (22.86 and 26.54 lbf.ft).
(m)
Safety the nut (7) with a new cotter pin (6).
(8)
If applicable, connect the interconnecting strut (Ref. TASK 27-51-44-400-001).
(9)
If applicable, install the flap kink seals (Ref. TASK 27-54-61-400-006).
(10) If applicable, retract the flaps fully (Ref. TASK 27-50-00-866-009). **ON A/C ALL
Subtask 27-54-00-942-065
B. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : ALL 1 27-54-00Page A608 1 1 May 01/05 1 1 1CES 1R **ON A/C 001-001, 051-052,
TASK 27-54-00-220-003
Detailed Inspection of Inboard Flap Trunnions for Evidence of Wear Marks
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 275100-04
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific spark-proof lamp
No specific warning notice
No specific access platform 3 m (9 ft. 10 in.)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
R 1EFF : 001-001, 051-052, 1 27-54-00Page A609 1 1 May 01/05 1 1 1CES 1 B. Consumable Materials 中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機(jī)維護(hù)手冊(cè) AMM FLIGHT CONTROLS 飛行操縱5(2)
