WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking plugs
No specific circuit breaker(s) safety clip(s)
No specific warning notice
No specific access platform 3.0 m (9 ft. 10 in.)
No specific container 5.0 l (1.3208 USgal)
98D27504005000 1 PIN RIGGING-FLAPS (TRACK 1)
R 98D27504006000 1 PIN RIGGING FLAPS 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-00-00-480-002 Installation of the Flap/Slat Control-Lever Locking
Tool (98D27803000000) 27-50-00-866-009 Retraction of the Flaps on the Ground 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action
29-14-00-614-001 Depressurization of the Hydraulic Reservoirs
32-12-00-010-001 Open the Main Gear Doors for Access
27-54-52-991-001 Fig. 401
3. Job Set-up
__________
Subtask 27-54-52-866-050
A. Retraction of the Flaps
(1)
Retract the flaps to the 0 degree position (Ref. TASK 27-50-00-866-009).
(2)
Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) (Ref. TASK 27-00-00-480-002) on the slat/flap control lever.
Subtask 27-54-52-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
R 49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
Subtask 27-54-52-010-050
C. Open the main doors of the main gear (Ref. TASK 32-12-00-010-001).
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 27-54-52-860-050
D. Aircraft Maintenance Configuration
(1)
Put the access platform in position at the opening of the main door of the main gear.
(2)
Make sure that the Green and Yellow hydraulic systems are depressurized and put them in the maintenance cofiguration (Ref. TASK 29-00-00-864-001).
(3)
Depressurize the reservoirs of the Green and the Yellow hydraulic systems (Ref. TASK 29-14-00-614-001).
(4)
Put the warning notice in position to tell persons not to pressurize the hydraulic systems.
(5)
Install the PIN RIGGING-FLAPS (TRACK 1) (98D27504005000) at the left and right flap track positions 1.
(6) Put a container in position below the Power Control Unit (PCU) (1). **ON A/C 301-399,
Subtask 27-54-52-860-050-A
D. Aircraft Maintenance Configuration
(1)
Put the access platform in position at the opening of the main door of the main gear.
(2)
Make sure that the Green and Yellow hydraulic systems are depressurized and put them in the maintenance cofiguration (Ref. TASK 29-00-00-864-001).
(3)
Depressurize the reservoirs of the Green and the Yellow hydraulic systems (Ref. TASK 29-14-00-614-001).
(4)
Put the warning notice in position to tell persons not to pressurize the hydraulic systems.
(5)
Install the PIN RIGGING FLAPS (98D27504006000) at the left and right flap track positions 1.
R (6) Put a container in position below the Power Control Unit (PCU) (1). R **ON A/C ALL
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱5(140)
