5. Close-up
________ Subtask 27-54-46-410-051
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the GROUND LOCK SLEEVE from the applicable MLG door actuator (Ref. TASK 32-00-00-481-002).
(3)
Close the applicable MLG door (Ref. TASK 32-12-00-410-001).
(4)
Remove the COLLAR-SAFETY, SPOILER from the piston rod of each servo-control.
(5)
Put the Nos. 1, 2, 3, 4 and 5 spoilers to the operation position (Ref. TASK 27-60-00-866-002).
Subtask 27-54-46-865-054
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 27-54-46-860-052
C. Aircraft Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever.
(2) Retract the flaps fully (Ref. TASK 27-50-00-866-009). Subtask 27-54-46-942-053
D. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
1EFF : ALL 1 27-54-46Page 609 1 1 May 01/04R 1 1 1CES 1
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-54-46Page 610 1 1 May 01/04R 1 1 1CES 1
TASK 27-54-46-200-002
Detailed Inspection of the Flap Carriage Rollers for In-Service Wear
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notice No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft) 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
1EFF : ALL 1 27-54-46Page 611 1 1 May 01/04R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
SYNTH.ESTER BASED GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 06-011 GB ABR 1-4055
SOLID FILM LUBRICANT (Ref. 20-31-00)
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
3 lock plates 27-54-46 01 -030 3 lock plates 27-54-46 01A-030 8 lock plates 27-54-46 01 -030 8 lock plates 27-54-46 01A-030 9 lock plates 27-54-46 01 -030 9 lock plates 27-54-46 01A-030 R 9 cotter pins 27-54-46 20 -070 19 cotter pins 27-54-46 04B-110 20 cotter pins 27-54-46 04B-110 R 20 cotter pins 27-54-46 22 -180 R 22 cotter pins 27-54-46 22 -220
D. Referenced Information
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱5(82)
