5. Close-up
________
 **ON A/C 001-049, 051-061, 101-103, 201-203,

 (Ref. Fig. 401/TASK 27-54-45-991-001) R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
 (Ref. Fig. 401A/TASK 27-54-45-991-001-A)
 **ON A/C ALL

 Subtask 27-54-45-410-055
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Install the applicable access panel:

 -
FOR 6214CM
 install 573BB

 -
FOR 6220CM
 install 575BB

 -
FOR 6264CM

 install 673BB

 -
FOR 6270CM
 install 675BB.

 Subtask 27-54-45-942-056
 B. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Remove the warning notice(s).

 (3)
 Remove the access platform(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 27-54-45Page 490 1 1 May 01/00R 1 1 1CES 1

 TASK 27-54-45-000-008
 Removal of the Torque Shafts 6216CM(6266CM)/6226CM(6276CM)
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notice No specific access platform 3.5 m (11 ft. 6 in.) 98D27504030001 1 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT 98D27604000000 1 COLLAR-SAFETY, SPOILER 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
 1EFF : ALL 1 27-54-45Page 491 1 1 May 01/00R 1 1 1CES 1

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-400-003 Installation of the Lock-Torque Shaft - Flaps and
 Slats (98D27504030001) 27-50-00-866-008 Extension of the Flaps on the Ground 27-60-00-866-002 Extension-Retraction of the Spoilers for Maintenance
 **ON A/C 001-049, 051-061, 101-103, 201-203,
 27-54-45-991-001 Fig. 401

R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
 27-54-45-991-001-A Fig. 401A
 **ON A/C 001-049, 051-061, 101-103, 201-203,
 27-54-45-991-003 Fig. 404

R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
 27-54-45-991-003-A Fig. 404A
 FOR FIN 6216CM
 57-51-37-000-002 Removal of the Access Panels 573AB(673AB),

 573BB(673BB), 573CB(673CB)
 FOR FIN 6226CM
 57-51-37-000-004 Removal of the Access Panels

 575AB/575BB/575CB/575DB/575EB/575FB/575GB/575HB
 (675AB/675BB/675CB/675DB/675EB/675FB/675GB/675HB) FOR FIN 6266CM 57-51-37-000-002 Removal of the Access Panels 573AB(673AB),
 573BB(673BB), 573CB(673CB)
 FOR FIN 6276CM
 57-51-37-000-004 Removal of the Access Panels

 575AB/575BB/575CB/575DB/575EB/575FB/575GB/575HB (675AB/675BB/675CB/675DB/675EB/675FB/675GB/675HB) **ON A/C ALL

 3. Job Set-up
__________
 **ON A/C 001-049, 051-061, 101-103, 201-203,

 (Ref. Fig. 401/TASK 27-54-45-991-001) R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
 (Ref. Fig. 401A/TASK 27-54-45-991-001-A)
 **ON A/C ALL

 Subtask 27-54-45-941-055
 A. Safety Precautions
 (1)
 Put the safety barriers in position.