(Ref. Fig. 401/TASK 27-54-45-991-001) R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
 (Ref. Fig. 401A/TASK 27-54-45-991-001-A) **ON A/C ALL

 Subtask 27-54-45-941-058
 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 Put a warning sign in position to tell persons not to operate the flap/slat controls.

 Subtask 27-54-45-860-061
 B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 (1)
 Extend the flaps fully (Ref. TASK 27-50-00-866-008).

 (2)
 Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) on the flap/slat control lever.

 Subtask 27-54-45-865-058
 C. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
 Subtask 27-54-45-010-059
 D. Get Access
 (1)
 Put the access platform in the applicable position.

 (2)
 Remove the applicable access panel:

 -
FOR 6228CM
 remove 575DB, 575EB

 -
FOR 6278CM
 remove 675DB, 675EB.

 1EFF : ALL 1 27-54-45Page A445 1 1 Aug 01/02R 1 1 1CES 1

 (3)
 Put the applicable spoiler in the 'M' (Maintenance) position (Ref. TASK 27-60-00-866-002).

 (4)
 Put the COLLAR-SAFETY, SPOILER on the piston rod of the servo-control.

 4. Procedure
_________
 **ON A/C 001-049, 051-061, 101-103, 201-203,

 (Ref. Fig. 401/TASK 27-54-45-991-001) R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
 (Ref. Fig. 401A/TASK 27-54-45-991-001-A)
 **ON A/C ALL

 (Ref. Fig. 405/TASK 27-54-45-991-004)
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING

_______
 EDGE:

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 Subtask 27-54-45-020-061
 A. Removal of the Torque Shaft 6228CM(6278CM)
 (1)
 Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (98D27504030001) on a flap torque shaft (Ref. TASK 27-50-00-400-003), outboard of the component to be removed.

 (2)
 Remove the nuts (89), the bolts (90) and the torque shaft (84).

 (3)
 Remove the retaining ring (87) and the pin (85).

 (4)
 Remove the torque shaft (86) and the universal joint (88).

 TASK 27-54-45-400-012 Installation of the Torque Shaft 6228CM(6278CM) WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______ NOTICES ARE IN POSITION.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice No specific access platform 3.5 m (11 ft. 6 in.) No specific Torque Wrench : range 0.20 to 3.60 m.daN
 (2.00 to 26.00 lbf.ft)
 1EFF : ALL 1 27-54-45Page A447 1 1 Aug 01/02R 1 1 1CES 1

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱5(57)