REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
32-42-27-991-002-A Fig. 601
**ON A/C 301-399,
32-42-27-991-002-B Fig. 601A
**ON A/C ALL
3. Job Set-up
__________
Subtask 32-42-27-860-053
A. Aircraft Maintenance Configuration
(1)
Pressurize the Green hydraulic system (Ref. TASK 29-10-00-863-001).
(2)
Pressurize the Yellow hydraulic system (Ref. TASK 29-10-00-863-002).
(3)
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
Subtask 32-42-27-941-054
B. Safety Precautions
(1)
Put the warning notices in the cockpit to tell persons not to operate the landing gear.
(2)
Make sure that the wheel chocks are in position.
(3)
Set the parking brake to the OFF position
(4)
On the panel 110VU, make sure that the PARK BRK control switch 73GG is in the OFF position.
1EFF : ALL 1 32-42-27Page 602 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-42-27-865-056
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 4GG M36 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 3GG M35 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 32-42-27-210-052-A
A. Inspection of the Brake
(1)
Make sure that there are no leaks on the Normal braking system.
(a)
On the panel 402VU, set the A/SKID & NOSE WHEEL switch to ON.
(b)
Push the brake pedals more than once.
(c)
Make sure that there are no leaks on the piston housing, the pistons and the hydraulic lines.
(2)
Make sure that there are no leaks in the alternate braking system.
(a)
On the panel 402VU, set the A/SKID & NOSE WHEEL switch to OFF.
(b)
Push the brake pedals more than once.
(c)
Make sure that there are no leaks on the piston housing, the pistons and the hydraulic lines.
(3)
Make sure that the bleed plugs, the temperature sensor and the self-sealing couplings are in the correct position.
1EFF : ALL 1 32-42-27Page 603 1 1 Aug 01/05 1 1 1CES 1
(4) With the brakes on, make sure that the wear indicators are in the limits.
NOTE : Measure the wear pin when the brake is cold (Brake temperature
____
less than 60 deg.C).
NOTE : When the end of either wear pin aligns with the machined
____ surface of the piston housing, the heat pack is fully worn. You must replace the brake unit (Ref. TASK 32-42-27-000-001). (Ref. Fig. 601/TASK 32-42-27-991-002-A)
NOTE : For a new brake, measure the distance between the end of the
____ wear pin and the machined surface of the piston housing. This distance must be 50mm (1.97 in) maximum. If more than the maximun value replace the brake (Ref. TASK 32-42-27-000-001) (Ref. TASK 32-42-27-400-001). (Ref. Fig. 601/TASK 32-42-27-991-002-A)
NOTE : The brake units usually have two wear pins.
____ If you find a brake that does not have the two wear pins: -the brake is serviceable if there is one wear pin and the wear pin is in the limits.
R -you must deactivate the brake if there is no wear pin on the R brake unit (Ref. TASK 32-42-00-040-003) .
**ON A/C 301-399,
Subtask 32-42-27-210-052-B
A. Inspection of the Brake
(1)
Make sure that there are no leaks on the Normal braking system.
(a)
On the panel 402VU, set the A/SKID & NOSE WHEEL switch to ON.
(b)
Push the brake pedals more than once.
(c)
Make sure that there are no leaks on the piston housing, the pistons and the hydraulic lines.
(2)
Make sure that there are no leaks in the Alternate braking system.
(a)
On the panel 402VU, set the A/SKID & NOSE WHEEL switch to OFF.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架7(20)
