(2)
Remove the warning notice(s).
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 32-42-27Page 613 1 1 Aug 01/05R 1 1 1CES 1
TASK 32-42-27-210-006 Inspection/Check of the Brake with the Wheel Removed
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-41-11-000-006 Removal of the MLG Wheel (2649GM,2650GM,2651GM,2652GM) 32-41-11-400-006 Installation of the MLG Wheel
(2649GM,2650GM,2651GM,2652GM) 32-42-27-000-001 Removal of the Brake (2641GM,2642GM,2643GM,2644GM) 32-42-27-400-001 Installation of the Brake
(2641GM,2642GM,2643GM,2644GM) 32-42-71-000-001 Removal of the MLG Axle Adaptor-Sleeves 32-42-71-400-001 Installation of the MLG Axle Adaptor-Sleeves 32-42-27-991-006 Fig. 602 32-42-27-991-007-A Fig. 603
3. Job Set-up
__________ Subtask 32-42-27-941-064
A. Safety Precautions
(1) Make sure that the wheel-chocks are in position.
(2) Set the parking brake to the OFF position. Subtask 32-42-27-860-063
B. Aircraft Maintenance Configuration
(1) Remove the wheel of the brake that you must examine (Ref. TASK 32-41-11-000-006) .
1EFF : ALL 1 32-42-27Page 614 1 1 May 01/04R 1 1 1CES 1
4. Procedure
_________
Subtask 32-42-27-210-061-A
A. Visual Inspection of the Brake
(1)
Make sure that there are no leaks of hydraulic fluid on the pistons, the hydraulic lines and the self-sealing couplings.
(2)
Examine the wear indicator.
(3)
Make sure that the heat packs are in the correct condition.
(a)
Make sure that the disks can move easily on the torque tube.
(b)
Examine the rotors and make sure that:
-
there is no creep on the outer edge
-
there are no cracks
-the rotor can move freely around the torque tube
-there is no damage to the drive blocks. . if there is damage:
*
if the damage is the limits of the acceptance criteria,
(Ref. Fig. 602/TASK 32-42-27-991-006)
*
if the damage is out of the limits of the acceptance
criteria,
(Ref. Fig. 603/TASK 32-42-27-991-007-A)
** replace the drive blocks (Ref. TASK 32-42-27-000-001) and
(Ref. TASK 32-42-27-400-001).
(c)
Make sure that there are no cracks on the stator assembly.
(d)
Make sure that there are no cracks or signs of too much heat on the torque tube.
(e)
Make sure that the probe of the temperature sensor moves freely.
(f)
Make sure that the finish of the hydraulic crown is in the correct condition.
(g)
Make sure that the play of the brake release is correct. Make sure that none of the pistons moves.
(h)
If the inspection shows damage that can prevent the normal operation of the brake unit, you must replace the brake unit. (Ref. TASK 32-42-27-000-001) (Ref. TASK 32-42-27-400-001) Remove the protectors of the axle and inspect it. (Ref. TASK 32-42-71-000-001) (Ref. TASK 32-42-71-400-001)
1EFF : ALL 1 32-42-27Page 615 1 1 May 01/04 1 1 1CES 1
Acceptance Criteria for the Drive Blocks Damaged
Figure 602/TASK 32-42-27-991-006
1EFF : ALL 1 32-42-27 Page 616
1 1 May 01/04
1 1
1CES 1
Acceptance Criteria for the Drive Blocks Damaged
Figure 603/TASK 32-42-27-991-007-A
1EFF : ALL 1 32-42-27 Page 617
1 1 May 01/04
1 1
1CES 1
5. Close-up
________ Subtask 32-42-27-860-064
A. Put the aircraft back to its initial configuration.
(1)
Install the wheel. (Ref. TASK 32-41-11-400-006)
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 32-42-27Page 618 1 1 May 01/04 1 1 1CES 1
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架7(23)
