-
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific safety barriers
 No specific warning notice

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
32-00-00-481-001 Installation of the Safety Devices on the Landing Gears 32-48-51-000-005 Removal of the Fan Assy (7GS,8GS,9GS,10GS) R 32-49-18-000-001 Removal of the Rotating Mechanism
R **ON A/C 001-049, 101-149, 151-199, 201-299,
 32-42-57-991-001 Fig. 401
 1EFF : ALL 1 32-42-57Page 401 1 1 May 01/05 1 1 1CES 1 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

**ON A/C 051-099,
 32-42-57-991-001-B Fig. 401A R **ON A/C 301-399, 401-499,
 32-42-57-991-001-A Fig. 401B
 **ON A/C ALL

 3. Job Set-up
__________
 **ON A/C 001-049, 101-149, 151-199, 201-299,

 (Ref. Fig. 401/TASK 32-42-57-991-001)
 **ON A/C 051-099,

 (Ref. Fig. 401A/TASK 32-42-57-991-001-B) R **ON A/C 301-399, 401-499,
 (Ref. Fig. 401B/TASK 32-42-57-991-001-A)
 **ON A/C ALL

 Subtask 32-42-57-941-050
 A. Safety Precautions
 (1)
 Make sure that the safety barriers are in position.

 (2)
 Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).

 1EFF : ALL 1 32-42-57Page 402 1 1 Aug 01/05 1 1 1CES 1

 Anti-Skid Tachometer
 Figure 401/TASK 32-42-57-991-001

R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 32-42-57Page 403 1 1 May 01/05 1 1 1CES 1

R  Anti-skid Tachometer 
R  Figure 401A/TASK 32-42-57-991-001-B 
R 1EFF :  051-099,  1  32-42-57 Page 404 
1  1  May 01/05
 1  1
 1CES  1

 Anti-skid Tachometer
 Figure 401B/TASK 32-42-57-991-001-A

R 1EFF : 301-399, 401-499, 1 32-42-57Page 405 1 1 Aug 01/05 1 1 1CES 1 (3) On the panel 400VU:

 -make sure that the landing-gear control-lever 6GA is in the DOWN position
 -put a warning notice in position to tell persons not to operate the landing gear.
 Subtask 32-42-57-865-054
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 4GG M36 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33
R **ON A/C 001-049, 101-149, 151-199, 201-299,
 Subtask 32-42-57-010-051
 C. Get Access
 (1)
 Loosen the nut (15) then hold the hubcap (17) and remove the clamp (16). Carefully remove the hubcap (17) laterally.

 (2)
 Remove the cotter pins (3), the nuts (2), the washers (1) and the screws (12). Discard the cotter pins (3). Make sure that the nut (4) does not move from its related position to the axle.

 (3)
 Remove the mounting sleeve (11).

 (4)
 Disconnect the connector (6) from the tachometer (7), and put the blanking caps on the disconnected electrical connections.

 1EFF : ALL 1 32-42-57Page 406 1 1 May 01/05 1 1 1CES 1 **ON A/C 051-099,

 Subtask 32-42-57-010-051-B
 C. Get Access
 (1)
 Remove the applicable brake fan assembly (Ref. TASK 32-48-51-000-005).

 (2)
 Remove the applicable rotating mechanism (Ref. TASK 32-49-18-000-001).

R **ON A/C 301-399, 401-499,
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架7(38)