(5)
 Install the overheat sensing element 81HF(80HF) (7) and 83HF(82HF) (2):

 (a)
 Remove the blanking caps from the connectors (19), (22), (23) and (24).

 (b)
 Install the connectors (22) and (23) in the flanged attachment (21).

 (c)
 Install the nut (20) on the connectors (22) and (23).

 (d)
 TORQUE the nut (20) to between 0.56 and 0.68 m.daN (49.55 and

 60.17 lbf.in).

 (e)
 Install the connectors (19) and (24) on the connectors (22) and (23).

 (f)
 TORQUE the connectors (19) and (24) to between 0.56 and 0.68 m.daN (49.55 and 60.17 lbf.in).

 1EFF : ALL 1 36-22-16Page 417 1 1 May 01/05R 1 1 1CES 1

 (6) Install the parts of the cables 21HF(37HF) (40) and 77HF(64HF) (44) (Ref. TASK 36-22-16-400-002) (that you removed to help the removal of the overheat sensing elements 56HF(72HF) (8) and 81HF(80HF) (7)). 
R R R  WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE LOCKWIRE. CUT,_______ REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
 (7) Safety the applicable connectors (19), (22), (23) and (24) and the nuts (20) with MISCELLANEOUS (Material No. 19-010).
 (8) Close all the clamps (25) to hold the applicable overheat sensing element (1), (2), (7) or (8). Lock the quick-release fasteners (27).
 Subtask 36-22-16-865-057
 C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 2HA1, 3HA1, 2HA2, 3HA2.
 Subtask 36-22-16-710-050
 D. Test
 (1) Do an operational test of the overheat detection system (Ref. TASK 36-22-00-710-001).
 5. Close-up________
 Subtask 36-22-16-410-050
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items. 
R R R R (2) Install the applicable access panels, (Ref. TASK 53-35-13-400-002), (Ref. TASK 53-35-11-400-001), (Ref. TASK 57-41-37-400-002), (Ref. TASK 57-41-37-400-005): - FOR 56HF, 81HF install 191EB, 191CT, 521AB, 521BB, 521CB
 - FOR 72HF, 80HF install 192EB, 192CT, 621AB, 621BB, 621CB
 - FOR 29HF, 83HF

 install 191EB, 191CT, 191BT, 521AB, 521BB, 521CB
 -FOR 45HF, 82HF install 192EB, 192CT, 192BT, 621AB, 621BB, 621CB.
 Subtask 36-22-16-865-058
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV.
 Subtask 36-22-16-860-064
 C. Aircraft Configuration
 (1) Retract the slats fully (Ref. TASK 27-80-00-866-005). Subtask 36-22-16-942-050
 D. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Remove the warning notice(s).

 (3)
 Remove the access platform(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 36-22-16Page 419 1 1 May 01/05R 1 1 1CES 1

 TASK 36-22-16-000-002

 Removal of the Cables 21HF(37HF),77HF(64HF)
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR.
 1. Reason for the Job__________________ 
R R  Self Explanatory
 2. Job Set-up Information______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific No specific No specific No specific No specific 98D27803000000  blanking capscircuit breaker(s) safety clip(s)safety barrierswarning noticeaccess platform 2.8 m (9 ft. 2 in.)1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R  27-80-00-866-004 36-22-16-991-001 36-22-16-991-005 36-22-16-991-006  Extending the Slats on the GroundFig. 401 Fig. 405 Fig. 408

 3. Job Set-up
__________

 (Ref. Fig. 401/TASK 36-22-16-991-001) Subtask 36-22-16-941-051
 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 Put a warning notice in position in the cockpit to tell persons not to operate the slat controls.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PNEUMATIC 氣源 2(120)