(1) Start procedure of APU Bleed-Air Supply The start sequence of the APU is complete when the APU acquires 95% speed (Ref. AMM 49-42-00). Above the acquired 95% speed the APU is obtainable for the supply of bleed-air and electrical power. An ECB 59KD logic, permits an APU speed decrease to 88% during normal APU operation before it automatically stops the bleed air. Information on the ECAM and the overhead panel shows that the APU is available : - on the EWD, (the green APU AVAIL indication comes on) - on the APU page of the SD, (the green AVAIL indication comes on) - on the APU overhead panel 25VU, (the green AVAIL legend on the APU
 START P/ BSW 2KA comes on.
 When the APU is available you can push the APU BLEED P/BSW on the
 overhead panel 25VU to start the APU bleed-air supply.

 1EFF : ALL 1 36-12-00Page 37 1 1 Aug 01/05R 1 1 1CES 1

 APU Bleed Indicating Figure 013
 1EFF : 1 1R 1CES  ALL  1 11 1 36-12-00 Page 38 Aug 01/05

 When you push the APU BLEED P/BSW :
 -
the blue ON legend on the P/BSW comes on

 -
the P/BSW sends a signal to the BMC

 -
the BMC starts a test of the sensing elements on the APU bleed-air duct and the left wing bleed-air ducts. If the test is correct the BMC tells the ECB to open the APU bleed load valve.

 NOTE : If the BMC 1 finds a leak in the APU bleed-air ducts, while
____ there is a Main Engine Start (MES) signal from the engines, it ignores the leak signal and tells the ECB to open the APU bleed load valve.
 (2) Stop of the APU Bleed-Air Supply To stop the APU bleed-air supply you push the APU BLEED P/BSW again:
 -
the blue ON legend on the APU BLEED P/BSW goes off,

 -
the APU BLEED P/BSW removes the ground signal from the BMCs,

 -
the BMCs send an OFF signal to the ECB,

 -
the ECB stops the supply of electrical power to the solenoid of the APU bleed load valve,

 -
the APU bleed load valve closes and stops the bleed air supply,

 - on the BLEED and APU pages of the SD, the green APU bleed-valve symbol is shown in the closed position.
 NOTE : If an APU emergency shutdown or an APU automatic shutdown
____ occurs, the APU bleed air supply stops automatically.
R **ON A/C 106-149, 211-299, 301-399, 401-499,
R **ON A/C 106-149, 211-299, 401-499,
 (Ref. Fig. 001)
 **ON A/C 301-399,
 (Ref. Fig. 001A)
R **ON A/C 106-149, 211-299, 301-399, 401-499,
 (Ref. Fig. 002)
R 1EFF : ALL 1 36-12-00Page 39 1 1 Aug 01/05 1 1 1CES 1

 A. APU Bleed-Air Supply-System (Ref. Fig. 013)
 (1) Start procedure of APU Bleed-Air Supply The start sequence of the APU is complete when the APU acquires 95% speed (Ref. AMM 49-42-00 ). Above the acquired 95% speed the APU is obtainable for the supply of bleed-air and electrical power. An ECB 59KD logic, permits an APU speed decrease to 88% during normal APU operation before it automatically stops the bleed air. Information on the ECAM and the overhead panel shows that the APU is available : - on the EWD, (the green APU AVAIL indication comes on) - on the APU page of the SD, (the green AVAIL indication comes on) - on the APU overhead panel 25VU, (the green AVAIL legend on the APU
 START P/ BSW 2KA comes on.
 When the APU is available you can push the APU BLEED P/BSW on the
 overhead panel 25VU to start the APU bleed-air supply.
 When you push the APU BLEED P/BSW :

 -
the blue ON legend on the P/BSW comes on

 -
the P/BSW sends a signal to the BMC

 -
the BMC starts a test of the sensing elements on the APU bleed-air duct and the left wing bleed-air ducts. If the test is correct the BMC tells the ECB to open the APU bleed valve.

 NOTE : If the BMC 1 finds a leak in the APU bleed-air ducts, while
____ there is a Main Engine Start (MES) signal from the engines, it ignores the leak signal and tells the ECB to open the APU bleed valve.
 (2) Stop of the APU Bleed-Air Supply To stop the APU bleed-air supply you push the APU BLEED P/BSW again:
 -
the blue ON legend on the APU BLEED P/BSW goes off,

 -
the APU BLEED P/BSW removes the ground signal from the BMCs,

 -
the BMCs send an OFF signal to the ECB,

 -
the ECB stops the supply of electrical power to the rotary actuator of the APU bleed control valve,

 -
the APU bleed valve closes and stops the bleed air supply,

 - on the BLEED and APU pages of the SD, the green APU bleed-valve symbol is shown in the closed position.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PNEUMATIC 氣源 2(54)