4. Procedure_________
R
Subtask 36-22-16-420-060
A. Preparation for Installation
(1) Clean the component interface and/or the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(2) Do an inspection of the component interface and/or the adjacent area.
(3) Make sure that the parts retained from the removed component are clean and in the correct condition.
R R (4) Examine the applicable overheat sensing element (14) and (17) for the correct condition. The element tube must not be twisted and the surface must be free of damage other than the limits that follow:
R (a) The maximum permitted depth of abrasions or dents is 0.05 mm (0.0019 in.).
R (b) The minimum permitted tube diameter at a dent is 1.78 mm (0.0700 in.).
(5) Remove the blanking caps from the overheat sensing element (14) or (17) connectors and examine the connectors for the correct condition. Put the blanking caps on the connectors again.
Subtask 36-22-16-420-053
R B. Installation of the Overheat Sensing Elements 26HF(42HF), 53HF(69HF)
CAUTION : REMOVE OR INSTALL THE SENSING ELEMENTS CAREFULLY. DO NOT TWIST,_______ BEND OR CAUSE KINKS IN THE SENSING ELEMENTS.
R NOTE : Obey the permitted tolerances for the installation of the sensing____ elements: (Ref. Fig. 406/TASK 36-22-16-991-009, 407/TASK 36-22-16-991-011)
(1) Carefully install the overheat sensing element (14) or (17) and install the applicable grommets (37). Do not remove the blanking caps until the overheat sensing element (14) or (17) is in the position for the connection.
R WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE LOCKWIRE.
_______ R CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE R TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
(5)
Safety the connectors (19), (22), (23), and (24) and the the nuts
(20) with MISCELLANEOUS (Material No. 19-010).
(6)
Close all the clamps (25) to hold the overheat sensing element (14) or (17). Lock the quick-release fasteners (27).
Subtask 36-22-16-865-066
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 3HA1, 2HA1, 3HA2, 2HA2.
Subtask 36-22-16-710-053
D. Test
(1) Do an operational test of the overheat detection system (Ref. TASK 36-22-00-710-001).
5. Close-up
________
Subtask 36-22-16-410-053
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
R (2) Install the applicable access panels (Ref. TASK 57-41-37-400-003), R (Ref. TASK 57-41-37-400-002), (Ref. TASK 57-41-37-400-006):
-
FOR 26HF, 53HF install 522AT, 522AB, 522CB, 522EB, 522FB
-
FOR 42HF, 69HF install 622AT, 622AB, 622CB, 622EB, 622FB.
Subtask 36-22-16-865-067
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV.
Subtask 36-22-16-860-070
C. Aircraft Configuration
(1) Retract the slats fully (Ref. TASK 27-80-00-866-005).
Subtask 36-22-16-942-053
D. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 36-22-16Page 459 1 1 May 01/05R 1 1 1CES 1
TASK 36-22-16-000-005
Removal of the Overheat Sensing Elements 27HF(43HF),50HF(66HF),23HF(39HF),54HF (70HF)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
R R Self Explanatory
2. Job Set-up Information
______________________
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PNEUMATIC 氣源 2(131)
