-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
49-00-00-860-004 APU Shutdown by External Power (GTCP 36-300) 49-90-00-600-001 Check Oil Level and Replenish (GTCP 36-300) 52-41-00-410-001 Close the APU Doors after Access 49-91-44-991-001 Fig. 401
3. Job Set-up
__________
Subtask 49-91-44-860-058
A. Aircraft Maintenance Configuration
(1)
Make sure that the aircraft electrical circuits are energized (Ref. TASK 24-41-00-861-002).
(2)
On the panel 25VU, make sure that the APU MASTER SW p/bsw is OFF.
(3)
Make sure that there is a warning notice in the cockpit to tell persons not to start the APU.
(4)
Make sure that hydraulic systems are depressurized
(Ref. TASK 29-00-00-864-001).
Subtask 49-91-44-865-054
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
4. Procedure
_________
(Ref. Fig. 401/TASK 49-91-44-991-001) Subtask 49-91-44-420-051
A. Installation of the Oil Cooler (8079KM)
(1)
Remove the blanking plugs from the oil cooler and the oil pipes.
(2)
Apply a thin layer of lubricant OILS (Material No. 03-002) to the new o-ring (9) and to the new o-ring (9).
(3)
Install the new O-rings (9) on the oil pipes (8).
(4)
Put the oil cooler (8079KM) (4) into position with the oil pipes (8) in their related positions.
(5)
Install the oil cooler (4) with the washers (11) and the bolts (10).
(6)
TORQUE the bolts (10) on the oil cooler to between 0.56 and 0.60 m.daN (49.55 and 53.09 lbf.in)
(7)
Install the oil pipes (8) to the thermal bypass valve (5) on the oil cooler (8079KM) (4) with the retainers (7) and the bolts (6).
NOTE : Make sure that the oil pressure and return pipes are connected
____ to their correct connections at the thermal bypass valve (5).
(8)
TORQUE the bolts (6) to between 0.28 and 0.33 m.daN (24.77 and 29.20 lbf.in).
(9)
Connect the cooling air inlet duct (2) and the outlet duct (3) with the clamps (1).
(10) TORQUE the clamps (1) to between 0.28 and 0.31 m.daN (24.77 and 27.43 lbf.in).
NOTE : To prevent damage to the ducts, do not overtighten the clamps
____
(1).
Subtask 49-91-44-865-055
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD.
Subtask 49-91-44-710-051
C. Leak Test
(1)
Start the APU (Ref. TASK 49-00-00-860-003) in order to pump oil into the oil cooler (8079KM) (4).
(2)
Stop the APU (Ref. TASK 49-00-00-860-004).
(3)
Make sure that the oil level of the APU is correct (Ref. TASK 49-90-00-600-001).
(4)
Examine the oil cooler (8079KM) (4) and outlet duct (3) for oil leaks. No leaks are permitted.
(5)
Examine the oil tubes (8) and (1) for oil leaks. No leaks are permitted.
5. Close-up
________ Subtask 49-91-44-410-051
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-410-001).
(3)
Remove the access platform(s). Subtask 49-91-44-860-057
B.
Aircraft Maintenance Configuration
(1)
Pressurize the reservoirs of the hydraulic systems.
(Ref. TASK 29-14-00-614-002).
(2)
De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
(3)
Remove the warning notice(s).
TASK 49-91-44-000-002 Removal of the Thermal By-Pass Valve (GTCP 36-300) WARNING : DO NOT TOUCH THE APU UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER 6(118)
