(11)
 Locate the oil cooler outlet duct (8) and band clamp (7) on the oil cooler lower flange.

 NOTE : Do not tighten the band clamps (4) and (7) at this time.
____
 (12)
 TORQUE the mount bolts (6)to 40.0 lbf.in (0.45 m.daN).

 (13)
 Remove the blanking caps from the tubes (2) and (14).

 (14)
 Insert the oil tube (2) into the oil cooler and attach the retaining collar to the tube mount boss studs with the two nuts (1).

 (15)
 TORQUE the two nuts (1) to between 48 and 53 lbf.in (0.54 and 0.59 m.daN).

 (16)
 Insert the oil tube (14) into the oil cooler and attach the retaining collar to the tube mount boss studs with the two nuts (13).

 (17)
 TORQUE the two nuts (13) to between 48 and 53 lbf.in (0.54 and 0.59 m.daN).

 (18)
 TORQUE the band clamp nuts (4) and (7) to between 24 and 26.5 lbf.in

 (0.27 and 0.29 m.daN).

 (19)
 Attach the oil cooler outlet duct (8) to the exhaust duct (10) with clamp (9).

 (20)
 TORQUE the V-band clamp nut (9) to between 35 and 45 lbf.in (0.39 and

 0.50 m.daN).

 (21)
 Put the new packing (12) (P/N M83248-1-905) on the drain plug (11).

 (22)
 Install the drain plug (11) on the oil cooler (5).

 (23)
 Torque the drain plug (11) to between 50 and 70 lbf.in (0.56 and 0.79 m.daN).

 Subtask 49-91-44-865-065
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD  Subtask 49-91-44-710-053

 C. Test for Leaks
 (1)
 Start the APU (Ref. TASK 49-00-00-860-005).

 (2)
 Make sure that the oil level of the APU is correct (Ref. TASK 49-90-00-600-004).

 (3)
 Examine the fan outlet duct (16), the oil cooler (5), the outlet duct

 (8) and the check valve connections for oil leaks. NOTE : No leaks are permitted.
____
 (4)
 Examine the oil tubes (13) and (1) for oil leaks.
 NOTE : No leaks are permitted.

____

 (5)
 Stop the APU (Ref. TASK 49-00-00-860-006).

 5. Close-up
________ Subtask 49-91-44-410-055
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Close the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-410-001).

 (3)
 Remove the access platform(s). Subtask 49-91-44-860-052

 B.
 Aircraft Maintenance Configuration

 (1)
 Pressurize the reservoirs of the hydraulic systems.
 (Ref. TASK 29-14-00-614-002).

 (2)
 De-energize the aircraft electrical circuits
 (Ref. TASK 24-41-00-862-002).

 (3)
 Remove the warning notice(s).

 COOLER - OIL ((GTCP 36-300)) - CLEANING/PAINTING
________________________________________________

R **ON A/C 001-003, 051-099, 401-499,
 TASK 49-91-44-100-001
 Remove and clean the Air/Oil Cooler (8079KM) and install Air/Oil Cooler
 (8079KM) (GTCP 36-300)

 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS
_______
 ONLY WITH A GOOD SUPPLY OF AIR.
 OBEY THE MANUFACTURERS INSTRUCTIONS.
 PUT ON PROTECTIVE CLOTHING.
 DO NOT GET THEM IN YOUR MOUTH.
 DO NOT SMOKE.
 DO NOT BREATHE THE GAS.
 THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
 GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.

 WARNING : USE A PROTECTIVE EYE SHIELD/GOGGLES WHEN YOU USE COMPRESSED AIR.
_______
 DEBRIS AND/OR HIGH PRESSURE AIR CAN DAMAGE YOUR EYES.

 CAUTION : PUT PLASTIC CAPS OR PLUGS ON ALL FUEL AND/OR LUBRICATION SYSTEM
_______ COMPONENTS AND LINES. IF YOU USE TAPE, CLOTH, OR METAL CAPS ON THEM, YOU CAN DAMAGE THE APU.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 499144-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking plugs
 No specific circuit breaker(s) safety clip(s)
 No specific warning notice
 No specific access platform 3.5 m (11 ft. 6 in.)
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER 6(125)