-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
4. Procedure
_________
(Ref. Fig. 401/TASK 49-94-15-991-001) Subtask 49-94-15-420-050
A. Install the Oil Temperature Sensor.
(1)
Apply a thin layer of lubricant OILS (Material No. 03-002) to the new O-ring (3).
(2)
Install the new O-ring (3) on the oil temperature-sensor (2).
(3)
Remove the blanking plug from the gearbox port.
(4)
Install the oil temperature-sensor (2).
(5)
TORQUE the oil temperature-sensor (2) to 80 lbf.in (0.90 m.daN).
(6)
Remove the blanking caps from the electrical connector (1).
(7)
Connect the electrical connector (1). Subtask 49-94-15-210-050
B.
Do a check of the oil quantity (Ref. TASK 49-90-00-600-007). Subtask 49-94-15-865-052
C.
Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD
R EFF : 001-049, 101-105, 107-107, 151-199, 49-94-15Page 407 201-210, Aug 01/05
CES Subtask 49-94-15-740-050
D. Do the BITE test of the oil sump temperature-sensor (Ref. TASK 31-32-00-860-001).
Subtask 49-94-15-710-050
E. Start and Operate the APU.
(1)
Close the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-410-001).
(2)
Start the APU (Ref. TASK 49-00-00-860-008).
(3)
Let the APU run for 5 minutes.
(4)
Shut down the APU (Ref. TASK 49-00-00-860-009).
(5)
Open the APU access doors 315AL, 316AR.
(6)
Do a leak check of the Oil Temperature-Sensor.
NOTE : No leaks are permitted.
____
(7)
Re-torque the oil temperature sensor (2) to to 80 lbf.in (0.90 m.daN).
5. Close-up
________ Subtask 49-94-15-865-053
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD
Subtask 49-94-15-410-050
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the container.
(3)
Set the LIGHT SW 11LJ to the OFF position.
(4)
Close the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-410-001).
R EFF : 001-049, 101-105, 107-107, 151-199, 49-94-15Page 408 201-210, Aug 01/05
CES
(5)
Remove the access platform(s). Subtask 49-94-15-860-053
C.
Aircraft Maintenance Configuration
(1)
Pressurize the reservoirs of the hydraulic systems. (Ref. TASK 29-14-00-614-002).
(2)
De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
(3)
Remove the warning notice(s).
R EFF : 001-049, 101-105, 107-107, 151-199, 49-94-15Page 409 201-210, Aug 01/05
CES
APU - OIL HEATING - DESCRIPTION AND OPERATION
_____________________________________________
R **ON A/C 001-003, 051-099, 401-499,
1.
General
_______ The APU oil heater 2KT increases the temperature of the oil in the APU gearbox oil reservoir if the oil temperature is too low.
2.
Component Location
__________________
(Ref. Fig. 001)
-------------------------------------------------------------------------------FIN | FUNCTIONAL DESIGNATION | PANEL|ZONE|ACCESS | ATA | | | | DOOR | REF. -------------------------------------------------------------------------------2KT HEATER - OIL APU 316 316AR 49-96-51
3. System Description
__________________ An oil temperature switch, which is part of the APU oil heater, monitors the oil temperature in the reservoir of the APU gearbox. If the oil temperature decreases below 70 DEG.F (21.11 DEG.C), the temperature switch closes and 115 V AC is supplied to a heater coil. This increase the APU oil temperature to more than the APU compartment temperature during cold soak condition. When the oil temperature increases to above 110 DEG.F (43.33 DEG.C) (in case of a warm APU compartment temperature condition). The temperature switch then opens, and stops the 115 V AC supply to the heater coil.
The sensors generator-oil temperature sensor and oil-sump temperature sensor
together with the ECB 59KD monitor the APU oil heater 2KT.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER 6(185)
