(5)
 Examine the hot nozzle (1) and the bellows (3) for damage, chafing marks or cracks. Replace them if they are defective.

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-81-42Page 403 201-210, Config-2 Aug 01/05
 CES

 Hot Nozzle and Bellows
 Figure 401/TASK 49-81-42-991-003

 CES  TASK 49-81-42-400-003

 Installation of the Hot Nozzle and Bellows (131-9(A))
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific  Torque Wrench : range 0.00 to 1.20 m.daN
 (0.00 to 9.00 lbf.ft)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
 the Ground Connector 49-81-41-000-003 Removal of the Exhaust Muffler (131-9(A)) 49-81-41-400-003 Installation of the Exhaust Muffler (131-9(A)) 52-41-00-010-001 Open the APU Doors for Access 52-41-00-410-001 Close the APU Doors after Access 52-41-18-000-001 Removal of the APU Exhaust Access-Fairing 317AL 52-41-18-400-001 Installation of the APU Exhaust Access-Fairing 317AL 49-81-42-991-003 Fig. 401

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-81-42Page 405 201-210, Config-2 Aug 01/05
 CES  3. Job Set-up

__________ Subtask 49-81-42-860-056
 A. Aircraft Maintenance Configuration
 (1)
 Energize the ground service network
 (Ref. TASK 24-42-00-861-001).

 (2)
 On the panel 25VU make sure that the APU MASTER SW p/bsw is OFF.

 (3)
 Make sure that there is a warning notice in the cockpit to tell persons not to start the APU.

 (4)
 Make sure that hydraulic systems are depressurized
 (Ref. TASK 29-00-00-864-001).

 (5)
 Make sure that the access platform is in position below the APU compartment.

 (6)
 Make sure that the APU access doors are open (Ref. TASK 52-41-00-010-001).

 (7)
 Set the LIGHT SW 11LJ to the ON position.

 (8)
 Make sure that the APU exhaust access-fairing 317AL is removed (Ref. TASK 52-41-18-000-001).

 (9)
 Make sure that the exhaust muffler is removed (Ref. TASK 49-81-41-000-003).

 Subtask 49-81-42-865-057
 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-81-42Page 406 201-210, Config-2 Aug 01/05
 CES  4. Procedure

_________ (Ref. Fig. 401/TASK 49-81-42-991-003) Subtask 49-81-42-420-052
 A. Installation of the Hot Nozzle and Bellows.
 (1)
 Install the bellows (3) on the exhaust muffler (5).

 (2)
 Install the clamp (4) on the bellows (3).

 (3)
 TORQUE the clamp (4) to between 0.2 and 0.22 m.daN (17.69 and 19.46 lbf.in).

 (4)
 Install the hot nozzle (1) on the exhaust muffler (5).

 (5)
 Put the drain line (7) in the six o'clock position.

 (6)
 Install the clamp (2) on the bellows (3).

 (7)
 TORQUE the clamp (2) to between 0.2 and 0.22 m.daN (17.69 and 19.46 lbf.in).

 (8)
 Install the exhaust muffler (Ref. TASK 49-81-41-400-003)

 5. Close-up
________ Subtask 49-81-42-410-052
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Set the LIGHT SW 11LJ to the OFF position.

 (3)
 Close the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-410-001).

 (4)
 Install the APU exhaust access-fairing (Ref. TASK 52-41-18-400-001).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER 6(52)