R  EFF : 001-049, 101-105, 107-107, 151-199, 49-81-00Page 608 201-210, Config-2 Aug 01/05
 CES

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
 the Ground Connector 49-81-41-000-001 Removal of the Exhaust Muffler (GTCP 36-300) 49-81-41-400-001 Installation of the Exhaust Muffler (GTCP 36-300) 52-41-00-010-001 Open the APU Doors for Access 52-41-00-410-001 Close the APU Doors after Access AIPC 49814101010 49-81-00-991-008 Fig. 602
 3. Job Set-up
__________
 Subtask 49-81-00-860-064
 A. Aircraft Maintenance Configuration
 (1)
 Energize the ground service network
 (Ref. TASK 24-42-00-861-001).

 (2)
 On the panel 25VU make sure that the APU MASTER SW pushbutton switch is off.

 (3)
 Put a warning notice in the cockpit to tell persons not to start the APU.

 (4)
 Make sure that hydraulic systems are depressurized
 (Ref. TASK 29-00-00-864-001).

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-81-00Page 609 201-210, Config-2 Aug 01/05
 CES  Subtask 49-81-00-865-066

 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
 Subtask 49-81-00-010-058
 C. Get Access
 (1)
 Put the access platform in position below the APU access doors 315AL and 316AR.

 (2)
 Open the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-010-001).

 (3)
 Set the LIGHT control SW 11LJ to the ON position.

 4. Procedure
_________ (Ref. Fig. 602/TASK 49-81-00-991-008) Subtask 49-81-00-210-060
 A. Disconnect the APU Exhaust Coupling for access.
 (1) Remove of the lockwire: WARNING : CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK.
_______
 LOOSE LOCKWIRE CAN CUT OR BLIND YOU.

 (a) Remove the lockwire from the upper and lower halves of the heat insulation (1) and (2), remove the heat insulation halves.
 (2)
 Remove the clamp (3) from the exhaust hot nozzle assy. and APU exhaust duct.

 (3)
 Push the hot nozzle and bellows assembly (7) as far rearwards as possible.

R  EFF : 001-049, 101-105, 107-107, 151-199, 49-81-00Page 610 201-210, Config-2 Aug 01/05
 CES

 Hot Nozzle and Sealing Ring - Inspection
 Figure 602/TASK 49-81-00-991-008

 CES  Subtask 49-81-00-210-061

 B. Visual Inspection
 (1)
 Examine the inner and outer flange areas of the hot nozzle assembly for distortion, wear-grooves and cracks. Replace if defective (Ref. AIPC 49814101010).

 (2)
 Use a hand mirror and examine the piston ring as far as possible for distortion, wear or damage. If the piston ring is found to be defective, replace the exhaust muffler (Ref. TASK 49-81-41-000-001) and (Ref. TASK 49-81-41-400-001).

 Subtask 49-81-00-420-057
 C. Connect the APU exhaust Coupling.
 (1)
 Push the hot nozzle/bellows assembly forward until the hot nozzle flange touches the APU exhaust duct flange.

 (2)
 Adjust the hot nozzle flange radially to the APU exhaust duct flange. The radial offset should be 0 +4 -4 mm (0.0 +0.16 -0.16 in.).

 (3)
 Position the clamp (3) on the exhaust coupling flanges with the lockbolts in the 3 and 9 o'clock position.

 (4)
 Secure the V-clamp (3). Torque the clamp lockbolts to between 0.81 and 0.93 m.daN (71.68 and 82.30 lbf.in).

 (5)
 Install the heat insulation upper (1) and lower (2) halves, connect the two halves with MISCELLANEOUS (Material No. 19-010).

 (6)
 Connect the two halves with corrosion-resistant steel lockwire 0.8mm (0.032in.) to the hot nozzle assembly studs.

 5. Close-up
________ Subtask 49-81-00-410-058
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER 6(37)