曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 WARNING: MAKE SURE THAT PERSONS OR EQUIPMENT ARE CLEAR OF THE
_______ LEADING EDGE FLAPS AND SLATS. THE LEADING EDGE CONTROL SURFACES WILL EXTEND. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 CAUTION: MAKE SURE THAT THE INBOARD FAN DUCT COWL AND THE THRUST
_______ REVERSERS ARE CLOSED OR COMPLETELY REMOVED BEFORE YOU EXTEND THE LEADING EDGE FLAPS. THERE IS NOT SUFFICIENT CLEARANCE FOR THE LEADING EDGE FLAPS TO EXTEND IF THE INBOARD FAN DUCT COWL AND THE THRUST REVERSER ARE IN THE OPEN (MAINTENANCE) POSITION. THIS CAN CAUSE DAMAGE TO EQUIPMENT.
 CAUTION: MAKE SURE THAT THE ALTERNATE FLAP DRIVE UNIT IS LIMITED TO
_______ 4 MINUTES OPERATION AND 25 MINUTES OFF. FAILURE TO DO THIS CAN CAUSE DAMAGE TO THE DRIVE UNIT.
 (d)  Set the ALTERNATE FLAPS position switch to DOWN.
 1)  Make sure that the leading edge flaps and slats operate satisfatory.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-09-45
 ALL  ú ú 01 Page 405 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (e)  
Set the ALTERNATE FLAPS position switch to UP.

 1)  Make sure that the leading edge flaps and slats operate satisfatory.

 (f)  
Set the ALTERNATE FLAPS arm switch to OFF. 1) Make sure that the leading edge flaps and slats fully

 retract. 2) Make sure that the trailing edge flaps fully retract.

 (g)  
Set the FLT CONTROL B switch to OFF.

 (h)  
Set the ALTERNATE FLAPS arm switch to ARM. 1) Make sure that the STANDBY HYD - LOW PRESSURE light comes

 on momentarily, then goes off. 2) Make sure that the flaps and slats do not extend.

 (i)  
Set the ALTERNATE FLAPS arm switch to OFF.

 (j)  
Set the FLT CONTROL B switch to ON.

 S 864-016
 (12)
 Remove electrical power if it is not necessary (AMM 24-22-00/201).

 (13)
 Remove hydraulic power if it is not necessary (AMM 29-15-00/201).

 S 864-018
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-09-45
 ALL  ú ú 02 Page 406 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 COMPENSATOR CARTRIDGE - REMOVAL/INSTALLATION
____________________________________________
 1.  General
_______
 A.  This procedure contains two tasks. There is one task for the removal and one task for the installation of the compensator cartridge.
 B.  The compensator cartridge is a part of the flight controls modular package. The modular package for hyraulic system A is found in the left main wheel well. The modular package for hydraulic system B is found in the right main wheel well.
 TASK 27-09-51-004-026
 2.  Compensator Cartridge Removal
_____________________________
 A.  References
 (1)  
AMM 29-09-00/201, Hydraulic Reservoir Pressurization System

 (2)  
AMM 29-15-00/201, Hydraulic Systems A, B, and Standby

 B.  
Access

 (1)  
Location Zones
 101/102 Control Cabin - Left/Right
 216/217 Left/Right Main Wheel Well

 C.  
Prepare for Removal

 S 864-002
 (1)  
Do this task to depressurize hydraulic systems A and B: "Hydraulic System A, B or Standby Depressurization" (AMM 29-15-00/201).

 S 864-003

 (2)  
Do this task to depressurize hydraulic system A and B reservoirs: "Hydraulic Reservoirs Depressurization" (AMM 29-09-00/201).

 D.  
Procedure

 S 024-029
 (1)  
Remove the compensator cartridge (Fig. 401):

 (a)  
Remove the compensator cartridge from the modular package.

 (b)  
Use a container to catch hydraulic fluid that drains from the compensator cartridge and the flight controls modular package.

 (c)  
Put a cover on the modular package housing to keep (unwanted) material out of the open port in the modular package housing.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(36)