27-09-71
 ALL  ú ú 01 Page 533 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 FLIGHT CONTROL SHEAR RIVETS - MAINTENANCE PRACTICES
___________________________________________________
 TASK 27-09-81-612-001
 1. General
_______
 A. General
 (1)  Shear fasteners are used so that function of necessary airplane components can continue when a connected component will not operate and will not move. Shear fasteners are usually bolts or rivets. Each shear fastener location is identified by a marker. This marker identifies the location as a Shear Joint. The marker also identifies the quantity and type of fastener that must be used to complete the joint. The table below identifies the components in the flight control systems where shear fasteners are used. The table below also identifies the maintenance manual subjects that give maintenance procedures for these shear fasteners.
 ~.............................................................................. | Subject No. | Rivet Type | Part Containing Fastener | ................................................................................ | AMM 27-11-14/801 | BACB30GP6-5 | Aileron Bus Drums | ................................................................................ | AMM 27-51-04/801 | BACR15BB4D9 | Exhaust Gate Actuator Rods | ................................................................................ | AMM 27-51-34/801 | BACR15BB4D9 | Exhaust Gate Actuator Rods | ................................................................................ | AMM 27-51-04/801 | BACR15BB5D10 | Exhaust Gate Actuator Rods | ................................................................................ | AMM 27-51-34/801 | BACR15BB5D10 | Exhaust Gate Actuator Rods | ................................................................................ | AMM 27-61-41/801 | MS 20470D | Spoiler Control Quadrant | ................................................................................ | AMM 27-61-61/801 | BACBB4AD | Flight Spoiler Control Quadrant | 2......................…..............…........................................1
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-09-81
 ALL  ú ú 01 Page 201 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 FLIGHT CONTROL HINGE BEARING DUST SEALS - APPROVED REPAIR
_________________________________________________________
 1.  General
_______
 A.  This procedure has one task. The task is a temporary repair of the flight control hinge bearing dust seals (which is referred to as the "dust seals").
 B.  This procedure provides instructions for temporary repair of the dust seals only. You must replace the dust seal at the first convenient time.
 TASK 27-09-83-308-001
 2.  Temporarily Repair the Flight Control Hinge Bearing Dust Seals
______________________________________________________________
 A.  Consumable Materials
 (1)  
D00377 Grease - Mobilgrease 28
 BMS 3-24 Grease (optional)

 B.  
Procedure

 S 028-002
 (1)  
Remove the dust seal.

 (2)  
Lubricate the flight control hinge bearings.

 S 648-003
 NOTE: If you replace the aileron or elevator hinge bearings, refer
____ to AMM 27-11-00/501 and AMM 27-31-00/501 for manual reversion flight test criteria.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-09-83
 ALL  ú ú 01 Page 801 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 FLIGHT CONTROLS SURFACE - INSPECTION/CHECK
__________________________________________
 1.  General_______
 A.  This procedure contains six tasks to make an inspection of the different flight control surfaces. These tasks are as follows:
 (1)  
The inspection of the aileron and aileron tabs

 (2)  
The inspection of the rudder

 (3)  
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 飛行操縱 FLIGHT CONTROLS 1(56)