C.
References

 (1)  
AMM 27-21-00/201, Rudder and Rudder Trim Control System

 D.
Access

 (1)  
Location Zone
 708 Rudder

 E.
Procedure

 S 866-004
 (1)
Pressurize the rudder hydraulic system (AMM 27-21-00/201).

 S 226-012

 (2)  
Do a check of the rudder play with no movement of the rudder pedal (Fig. 603):

 CAUTION: DO NOT PUT MORE THAN 50 POUNDS (222 NEWTONS) ON THE RUDDER
_______ WHEN YOU MOVE THE RUDDER SURFACE BY EXTERNAL FORCE. YOU CAN CAUSE DAMAGE TO THE RUDDER
 (a)  Use a block and scale to move the rudder to the left side with a force of 12.0 +/- 4 pounds (53 +/- 17 newtons) and release slowly.
 NOTE: Apply the force approximately 6-8 inches (152-203
____ millimeters) from the bottom of the trailing edge and 3 inches (76 millimeters) forward of the trailing edge.
 1) Make a record of the rudder position on the dial indicator.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-09-91
 ALL  ú ú 02 Page 606 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

A-A

Rudder Free-Play Check
Figure 603

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-09-91
 ALL  ú ú 02 Page 607 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
G57454
A
737-300/400/500MAINTENANCE MANUAL
 (b)  Use a block and scale to move the rudder to the right side with a force of 12.0 +/- 4 pounds (53 +/- 17 newtons) and release slowly.
 NOTE: Apply the force approximately 6-8 inches (152-203
____ millimeters) from the bottom of the trailing edge and 3 inches (76 millimeters) forward of the trailing edge.
 1) Make a record of the rudder position on the indicator.
 (c)  
Make sure the difference between the left and right positions is not more than 0.04 inch (1.0 millimeter). 1) If the difference is more than 0.04 inch (1.0 millimeter),

 then replace the bearings on the rudder hinge or power control units. ,

 (d)  
Use a block and scale to move the rudder to the left side with a force of 12.0 +/- 4 pounds (53 +/- 17 newtons) and release slowly.

 NOTE: Apply the force approximately 6-8 inches (152-203
____ millimeters) from the bottom of the trailing edge and 3 inches (76 millimeters) forward of the trailing edge.
 1) Make a record of the rudder position on the indicator.
 (e)  
Make sure the difference between the two left positions is not more than 0.02 inch (0.5 millimeter).

 (f)  
Remove the indicator from the rudder.

 F.
Put the Airplane Back to Its Usual Condition

 S 866-025
 (1)  Release the pressure from the rudder hydraulic system (AMM 27-21-00/201).
 TASK 27-09-91-206-005
 4. Elevator and Elevator Tab Inspection
____________________________________
 A. General
 (1)  
The control surface movement in the specified limits is permitted if the worn areas are equal in all the mechanical parts of the system. If a local area wears more quickly than the other areas in the system, repair that part of the system.

 (a)  
The limits are provided in Fig. 601.

 (2)  
Measure the movement with the control surface in the approximate aligned position at the surface inboard trailing edge unless otherwise noted.

 B.
Standard Tools and Equipment

 (1)  
Dial Indicator - Accurate to 0.001 inch

 (2)  
Spring Force Scale, Push Type - Capable of 15 +/- 0.2 pounds

 (3)  
Mounting Device (to hold the dial indicator against the elevator tab)

 C.
References

 (1)  
AMM 27-31-00/201, Elevator and Tab Control System

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(59)