曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(5) Do this task: Spoiler Hydraulic Systems A and B Pressurization, TASK 27-61-00-800-801.
SUBTASK 27-61-11-860-010
(6) Move the speed brake lever to the DOWN position to lower the spoilers.
SUBTASK 27-61-11-860-011
(7) Do this task: Retract the Trailing Edge Flaps, TASK 27-51-00-860-804.
SUBTASK 27-61-11-860-012
(8) Do this task: Put the Spoiler Hydraulic systems A and B Back to the Condition Before the
Pressurization, TASK 27-61-00-840-801.
SUBTASK 27-61-11-820-001
(9) Do this task: Flight Spoiler Adjustment, TASK 27-61-00-820-803.
SUBTASK 27-61-11-720-001
(10) Do this task: Flight Spoiler System Test (Alternate Method), TASK 27-61-00-000-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-11
Page 414
Jun 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SPOILER SHUTOFF VALVE - REMOVAL/INSTALLATION
1. General
A. This procedure has these tasks:
(1) A removal of the spoiler shutoff valve
(2) An installation of the spoiler shutoff valve
(3) A removal of the spoiler shutoff valve motor
(4) An installation of the spoiler shutoff valve motor.
B. The spoiler shutoff valve and the flight controls shutoff valve are parts of the flight controls hydraulic
module.
C. The spoiler shutoff valve is referred to as the "valve" and the spoiler shutoff valve motor is referred
to as the "valve motor" in this procedure.
D. You can replace the valve motor with the valve installed in the flight controls hydraulic module.
TASK 27-61-12-000-801
2. Spoiler Shutoff Valve Removal
(Figure 401)
A. General
(1) This task is the removal of the spoiler shutoff valve assembly, which contains the motor and the
valve.
B. References
Reference Title
29-09-00-860-802 Hydraulic Reservoirs Depressurization (P/B 201)
29-11-00-860-805 Hydraulic System A or B Power Removal (P/B 201)
29-11-01-860-802 Hydraulic Reservoirs Depressurization (P/B 201)
32-00-01-480-801 Landing Gear Downlock Pins Installation (P/B 201)
C. Tools/Equipment
Reference Description
STD-1154 Container - 5 Gallon (19 Liters)
D. Location Zones
Zone Area
133 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Left
134 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Right
211 Flight Compartment - Left
212 Flight Compartment - Right
E. Prepare for the Removal
SUBTASK 27-61-12-480-001
WARNING: MAKE SURE THE DOWNLOCK PINS ARE INSTALLED ON ALL THE LANDING GEAR.
WITHOUT THE DOWNLOCK PINS, THE LANDING GEAR COULD RETRACT AND CAUSE
INJURIES TO PERSONS AND DAMAMGE TO EQUIPMENT.
(1) If the downlock pins are not installed on all the landing gear, do this task: Landing Gear
Downlock Pins Installation, TASK 32-00-01-480-801.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-12
Page 401
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-61-12-860-001
(2) For applicable hydraulic system, do this task: Hydraulic System A or B Power Removal,
TASK 29-11-00-860-805.
NOTE: Remove power from hydraulic system A for the valve in the left wheel weel. Remove
power from hydraulic system B for the valve in the right wheel well.
SUBTASK 27-61-12-860-002
(3) Do this task: Hydraulic Reservoirs Depressurization, TASK 29-11-01-860-802 or Hydraulic
Reservoirs Depressurization, TASK 29-09-00-860-802.
SUBTASK 27-61-12-860-003
(4) Open this circuit breaker and install safety tag:
F/O Electrical System Panel, P6-2
Row Col Number Name
B 12 C00204 FLIGHT CONTROL SHUTOFF VALVES SPOILER
F. Spoiler Shutoff Valve Removal
SUBTASK 27-61-12-020-001
(1) Remove the housing valve assembly [12]:
(a) Disconnect the electrical connector [1] from the valve motor [7].
(b) Put a 5 gallon (19 liter) container, STD-1154 below the housing valve assembly [12] to catch
hydraulic fluid that drains from the housing valve assembly [12].
(c) Remove the four bolts [4] and washers [5] that attach the housing valve assembly [12] to
the hydraulic module housing [2].
(d) Carefully lift the housing valve assembly [12] straight up to remove it from the hydraulic
module housing [2].
(e) Put a cover on the hydraulic module housing [2] to keep contamination out of the open
valve hole.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊6 AIRCRAFT MAINTENANCE MANUA(32)