曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

the flaps.
NOTE: Turning the piston rod 1/4 turn will change the clearance by approximately 0.09
inches.
(e) Tighten the check nut [55].
(f) Check the adjustment.
1) Do this task: Speed Brake Hydraulic Systems A and B Pressurization,
TASK 27-62-00-800-801.
2) Retract the flaps (Retract the Trailing Edge Flaps, TASK 27-51-00-860-804).
3) Slowly move the speed brake lever to the DOWN position.
4) Make sure the clearances between the spoilers and the flaps are within the tolerances.
5) Turn the control wheel fully clockwise.
a) Make sure spoilers No. 2, 3, 4, and 5 do not move down.
b) If the spoilers move down, go back to the start of the task.
NOTE: You do not need to check the fit of the rig pins a second time.
6) Turn the control wheel back to neutral to retract the flight spoilers.
7) Turn the control wheel fully counterclockwise.
a) Make sure spoilers No. 8, 9, 10, and 11 do not move down.
b) If the spoilers move down, go back to the start of the task.
NOTE: You do not need to check the fit of the rig pins a second time.
(g) Extend the flaps (Extend the Trailing Edge Flaps, TASK 27-51-00-860-803).
(h) Move the speed brake lever to the full up position to extend the spoilers.
(i) Clean all grease from the piston rod and the actuator rod end [56] threads with Series 84
solvent, B01004 (TASK 20-30-84-910-801).
(j) Apply a layer of the corrosion preventive compound to the threads of the actuator rod
end [56].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-00
Page 523
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(k) Tighten the check nut [55] to 250 - 300 pound-inches (28.2 - 33.9 newton-meters).
(l) Install the lockwire, G01912 on the check nut [55].
(m) Apply a bead of sealant, A00247 to the check nut [55].
SUBTASK 27-61-00-860-122
(6) Check the adjustment of the spoiler actuator linkage. Do this task Spoiler Actuator Linkage
Adjustment, TASK 27-61-00-820-804.
SUBTASK 27-61-00-820-038
(7) Do this task: Flight Spoiler System Test (Alternate Method), TASK 27-61-00-000-801.
G. Put the Airplane Back to Its Usual Condition
SUBTASK 27-61-00-860-029
(1) Move the speed brake lever to the DOWN position to lower the spoilers, if it is necessary.
SUBTASK 27-61-00-860-030
(2) Do this task: Retract the Trailing Edge Flaps, TASK 27-51-00-860-804.
SUBTASK 27-61-00-860-031
(3) Make sure the clearance between the spoiler and the flap is in the limits.
SUBTASK 27-61-00-860-032
(4) Do this task: Put the Speed Brake Hydraulic systems A and B Back to the Condition Before
the Pressurization, TASK 27-62-00-840-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-00
Page 524
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Flight Spoiler Adjustment
Figure 503 (Sheet 1 of 4)/27-61-00-990-805
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-00
Page 525
Feb 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Flight Spoiler Adjustment
Figure 503 (Sheet 2 of 4)/27-61-00-990-805
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-00
Page 526
Feb 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Flight Spoiler Adjustment
Figure 503 (Sheet 3 of 4)/27-61-00-990-805
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-00
Page 527
Feb 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Flight Spoiler Adjustment
Figure 503 (Sheet 4 of 4)/27-61-00-990-805
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-00
Page 528
Feb 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-61-00-820-804
6. Spoiler Actuator Linkage Adjustment
(Figure 503)
A. References
Reference Title
24-22-00-860-811 Supply Electrical Power (P/B 201)
27-51-00-860-803 Extend the Trailing Edge Flaps (P/B 201)
27-51-00-860-804 Retract the Trailing Edge Flaps (P/B 201)
27-62-00-800-801 Speed Brake Hydraulic Systems A and B Pressurization (P/B 201)
27-62-00-840-801 Put the Speed Brake Hydraulic systems A and B Back to the
Condition Before the Pressurization (P/B 201)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊6 AIRCRAFT MAINTENANCE MANUA(8)