曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

PROCEDURES
NORMAL PROCEDURES
STANDARD OPERATING PROCEDURES - ENGINE START
A318/A319/A320/A321 FLEET PRO-NOR-SOP-08 P 5/10
FCOM 19 AUG 10
Note: A PTU FAULT is triggered, if the second engine is started within 40 s following the end
of the cargo doors operation.
AUTOMATIC ENGINE START
Applicable to:
Abort the engine start (if vibration indications are available), when the N2 vibration level exceeds
the 5 units advisory threshold (indication pulses green), because this may indicate a bowed rotor
condition.
Initiate the subsequent start after the engine has completely spooled down. Do not complete
subsequent starts, until the vibration level is below 5 units. It is anticipated that the second start will
fall within the 5 units limit. This procedure may be repeated a maximum of three times.
In the log book report any N2 vibration advisory condition.
Use the automatic engine start procedure in most circumstances. However, if the start aborts due
to insufficient starter inlet air pressure (e.g. on high airfields, or in case of low pressure from an
external pneumatic power group), it is recommended to use the manual start procedure, instead the
automatic procedure.
If, during the engine start, the ground crew reports a fuel leak from the engine drain mast, run the
engine at idle for 5 min. If the leak disappears during these 5 min, the aircraft can be dispatched
without maintenance action. If the leak is still present after 5 min, maintenance action may be
required before the flight.
ENG MODE selector........................................................................................................... IGN/START
The lower ECAM displays the ENG SD page.
START ENGINE 2..............................................................................................................ANNOUNCE
Engine 2 is usually started first. It powers the yellow hydraulic system, that pressurizes the parking
brake.
ENG 2 MASTER sw..........................................................................................................................ON
Do not turn the ENG 2 MASTER sw ON before ‐ all amber crosses, except on N1 and N2, and
messages, have disappeared on the engine parameters (upper ECAM display).
‐ The N1 and N2 indications show amber crosses until the actual N1 and N2 reach about 3.5 %.
‐ Parameter callouts are not mandatory.
‐ In case the electrical power supply is interrupted during the start sequence (indicated by the loss
of ECAM DUs), abort the start by switching OFF the ENG 2 MASTER sw. Then, perform a 30 s
dry crank.
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
STANDARD OPERATING PROCEDURES - ENGINE START
A318/A319/A320/A321 FLEET PRO-NOR-SOP-08 P 6/10
FCOM 19 AUG 10
ON ECAM UPPER DISPLAY ON ECAM LOWER DISPLAY
N2 increases Corresponding start valve inline.
Bleed pressure indication green.
Oil pressure increases.
30 s after ENG 2 MASTER sw is ON:
‐ FF increases.
Indication of the active igniter (A or B).
20 s (maximum) after fuel is on
‐ EGT increases
‐ N1 increases prior to 34 % N2.
At 43 % N2 Igniter indication off.
Slightly above 43 % N2 Start valve crossline.
Note: When the FADEC detects an impending hung start or hot start, the FADEC applies an
automatic recovery sequence without an ECAM message. The crew will notice that dual
ignition (A+B) is applied, and that fuel will be commanded OFF, and then re-commanded
ON within 0.5 s. It is not necessary for the crew to shut down the engine.
MAIN AND SECONDARY ENG. IDLE PARAMETERS.............................................CHECK NORMAL
At ISA sea level : N1 about 21.4 %
N2 about 57.8 %
EPR about 1.01
EGT about 414 °C
FF about 350 kg/h (775 lb/h)
Grey background on N2 indication disappears.
START ENGINE 1..............................................................................................................ANNOUNCE
ENG 1 MASTER sw..........................................................................................................................ON
Same procedure as for engine 2.
Both pack valves reopen with 30 s delay after the second engine N2 is above 50 %.
Note: A PTU FAULT is triggered, if the second engine is started within 40 s following the end of
the cargo doors operation.
AUTOMATIC ENGINE START
Applicable to:
Abort the engine start (if vibration indications are available), when the N2 vibration level exceeds
the 5 units advisory threshold (indication pulses green), because this may indicate a bowed rotor
condition.
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320機組操作手冊FLIGHT CREW OPERATING MANUAL 11(141)