SPOILER 1 - REMOVAL/INSTALLATION
________________________________
TASK 27-64-41-000-001
Removal of the Spoiler 1
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific supports No specific warning notice No specific access platform 3.5 m (11 ft. 6 in.) SL90-314-4375 1 TOOL - EXTRACTION, TAB WASHERS STA-LOK NSA5454 SL90-314-6250 1 TOOL - EXTRACTION, TAB WASHERS STA-LOK NSA5454 SL90-314-7500 1 TOOL - EXTRACTION, TAB WASHERS STA-LOK NSA5454 SL90-315-4375 1 WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454 SL90-315-6250 1 WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454 SL90-315-7500 1 WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454
1EFF : ALL 1 27-64-41Page 401 1 1 May 01/05R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
20-22-00-000-001 Removal of STA-LOK Nuts and Lockwashers 27-60-00-866-002 Extension-Retraction of the Spoilers for Maintenance 57-51-37-000-002 Removal of the Access Panels 573AB(673AB),
573BB(673BB), 573CB(673CB)
**ON A/C 001-003, 051-052,
27-64-41-991-001 Fig. 401 R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 401-499,
27-64-41-991-001-A Fig. 401A
**ON A/C 301-399,
27-64-41-991-001-B Fig. 401B
**ON A/C 001-003, 051-052,
27-64-41-991-002 Fig. 402 R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
27-64-41-991-002-A Fig. 402A
**ON A/C ALL
3. Job Set-up
__________
**ON A/C 001-003, 051-052,
(Ref. Fig. 401/TASK 27-64-41-991-001)R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 401A/TASK 27-64-41-991-001-A)
**ON A/C 301-399,
(Ref. Fig. 401B/TASK 27-64-41-991-001-B)
**ON A/C ALL
Subtask 27-64-41-941-050
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in position to tell persons not to pressurize the hydraulic system.
(3)
Put a warning notice in position to tell persons not to operate the flight controls.
Subtask 27-64-41-860-050
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Extend the spoiler 1 (Ref. TASK 27-60-00-866-002).
(2)
Make sure the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is on the flap and slat control lever on panel 114VU.
(3)
Make sure the COLLAR-SAFETY, SPOILER is on the piston rod of the servo-control.
Spoiler 1 - Actuator Detail and Clearances Figure 401/TASK 27-64-41-991-001- 12 (SHEET 1)
R 1EFF : 001-003, 051-052, 1 27-64-41Page 404 1 1 May 01/05 1 1 1CES 1
Spoiler 1 - Actuator Detail and Clearances Figure 401/TASK 27-64-41-991-001- 22 (SHEET 2)
R 1EFF : 001-003, 051-052, 1 27-64-41Page 405 1 1 May 01/05 1 1 1CES 1
Spoiler 1 - Actuator Detail and Clearances
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱6(120)
