(2)
 To adjust the cruise roller (234), do the steps that follow:

 (a)
 If necessary, remove the cushion seal (229).

 (b)
 Remove the nut (232), the collar (231) and the serrated plate (233).

 1EFF : 301-399, 1 27-54-61Page A435 1 1 Aug 01/05R 1 1 1CES 1

 Cruise Roller Adjustment
 Figure 427/TASK 27-54-61-991-040
 1EFF :  301-399,  1  27-54-61 Page A436 
1  1  Aug 01/05
 1R 1 
1CES  1

 (c)
 Turn the eccentric (230) until the dimension T is correct.

 (d)
 Install the serrated plate (233) to lock the eccentric (230).

 (e)
 Install the collar (231) and the nut (232). Tighten the nut (232) by hand.

 (f)
 Do a check of the dimension U and the dimension T again.

 (g)
 TORQUE the nut (232) to between 4.8 and 5.4 m.daN (35.39 and

 39.82 lbf.ft).
 (3)
 Measure and record the clearance between the bottom surface of the shroud box and the top surface of the flap (measured at the outboard end of the shroud box). The clearance must be between 5 mm (0.1968 in.) and 12 mm (0.4724 in.).

 (4)
 Do a check of the clearance between the trailing edge of the spoiler 1 and the top surface of the flap (Ref. TASK 27-64-00-820-001).

 Subtask 27-54-61-420-083
 M. Installation of the Z-coupling
 (Ref. Fig. 417/TASK 27-54-61-991-019)

 (1)
 Remove the Z-coupling lever (25) from the inboard flap
 attachment-bracket (21):

 (a)
 Remove the nut (23), the washer (24), the bolt (20) and the lever (25).

 (b)
 Remove the nut (17), the washer (18) and the spacer(s) (19).

 (2)
 Put the lever (25) in position on the lever (15) and at the inboard flap attachment-bracket (21).

 (3)
 Temporarily install the bolt (20).

 (4)
 Measure and write down the minimum value of the dimension F that can be measured between the levers (25) and (15):

 (a)
 Subtract 2 mm (0.0787 in.) from the dimension F and use sufficient spacer(s) (19) to get the remaining thickness.

 (b)
 If the dimension F is less than 2 mm (0.0787 in.), put the spacer(s) (19) between the lever (15) and the washer (18).

 1EFF : 301-399, 1 27-54-61Page A437 1 1 Aug 01/05R 1 1 1CES 1

 (c) If there is no gap between the levers (25) and (15), apply a load to the outboard end of the inner flap to get a gap of 0.1 mm (0.0039 in.). The load must be applied vertically in line with the lever (25) and must not be more than 20 daN (45 lbf).
 (5)
 If necessary, remove the bolt (20) and the lever (25).

 (6)
 Install the lever (25) with the correct thickness of spacer(s) (19) between the levers (25) and (15).

 (7)
 Install the bolt (20).

 (8)
 Make sure that the rigging pin (180) is removed at the track 1 position.

 (9)
 Use the pneumatic wrench and the ADAPTOR-DRIVE, SLAT (AND FLAP) to extend the flaps to position 1.

 (10)
 Install the washer (24) and the nut (23).

 (11)
 TORQUE the nut (23) to between 0.9 and 1 m.daN (79.64 and 88.49 lbf.in).

 (12)
 Safety the nut (23) with a new cotter pin (22).

 (13)
 Use the pneumatic wrench and the ADAPTOR-DRIVE, SLAT (AND FLAP) to retract the flaps to the 0 position.

 (14)
 Install the remaining spacers(s) (19) above the washer (18) and the nut (17).

 (15)
 TORQUE the nut (17) to between 3.1 and 3.6 m.daN (22.86 and 26.54 lbf.ft).

 (16) Safety the nut (17) with a new cotter pin (16). Subtask 27-54-61-860-065
 N. Aircraft Configuration
 (1)
 Install the interconnecting strut (Ref. TASK 27-51-44-400-001)

 (2)
 Install the right angle gearbox (Ref. TASK 27-54-41-400-001).

 (3)
 Remove the ADAPTOR-DRIVE, SLAT (AND FLAP) (98D27804001000).

 (4)
 Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000).

 1EFF : 301-399, 1 27-54-61Page A438 1 1 Aug 01/05R 1 1 1CES 1

 (5) Extend the flaps to position 1 (Ref. TASK 27-50-00-866-008).
 (6) Install the flap kink seals (Ref. TASK 27-54-61-400-006). Subtask 27-54-61-410-053
 P. Close Access
 (Ref. Fig. 416/TASK 27-54-61-991-016)

 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱6(52)