Subtask 27-64-41-220-074
Z. Dimensions of the Spoiler 1
NOTE : Limits on chrome plated items only apply when there is a layer of
____
chrome remaining on the bearing surfaces.
(1) Complete an inspection of these dimensions.
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | F | 22.184 | 22.205 | | | 22.164 | | | | OD 3 |(0.8733) |(0.8742) | | |(0.8725) | | | | | | | 0.008 | 0.041 | | | 0.090 | | | | | (0.0003)| (0.0016)| | |(0.0035)| | F | 22.213 | 22.225 | | | | 22.254 | | | ID 6 |(0.8745) |(0.8750) | | | |(0.8761) | | -------------------------------------------------------------------------------
Subtask 27-64-41-220-075
AA. Dimensions of the Spoiler 1
NOTE : Limits on chrome plated items only apply when there is a layer of
____
chrome remaining on the bearing surfaces.
(1) Complete an inspection of these dimensions.
1EFF : ALL 1 27-64-41Page 623 1 1 May 01/04R 1 1 1CES 1
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | F | 28.534 | 28.555 | | | 28.493 | | | | OD 4 |(1.1233) |(1.1242) | | |(1.1217) | | | | | | | 0.020 | 0.062 | | | 0.144 | | | | | (0.0007)| (0.0024)| | |(0.0056)| | F | 28.575 | 28.596 | | | | 28.637 | | | ID 5 |(1.1250) |(1.1258) | | | |(1.1274) | | -------------------------------------------------------------------------------
Subtask 27-64-41-220-076
AB. Dimensions of the Spoiler 1
NOTE : Limits on chrome plated items only apply when there is a layer of
____
chrome remaining on the bearing surfaces.
(1) Complete an inspection of these dimensions.
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | F | 22.184 | 22.205 | | | 22.143 | | | | OD 3 |(0.8733) |(0.8742) | | |(0.8717) | | | | | | | 0.020 | 0.062 | | | 0.144 | | | | | (0.0007)| (0.0024)| | |(0.0056)| | F | 22.225 | 22.246 | | | | 22.287 | | | ID 4 |(0.8750) |(0.8758) | | | |(0.8774) | | -------------------------------------------------------------------------------
5. Close-up
________ Subtask 27-64-41-410-051
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Install the spoiler 1 (Ref. TASK 27-64-41-400-001). Subtask 27-64-41-942-053
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護(hù)手冊 AMM FLIGHT CONTROLS 飛行操縱6(136)
