Flap Forward Eccentrics - Location and Detail Figure 407/TASK 27-54-62-991-003-A
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-62Page 427 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 27-54-62-420-078
P. Continue to Safety the Flap to the Flap Carriage Connections. (Ref. Fig. 403/TASK 27-54-62-991-010)
(1)
TORQUE the failsafe hook nuts (145) to 0.12 m.daN (10.61 lbf.in) maximum.
(2)
Safety the failsafe hook nuts (145) with MISCELLANEOUS (Material No. 19-010).
**ON A/C 001-001,
Subtask 27-54-62-820-052
Q. Adjustment of the Blade Seal and Cruise Roller
(1)
Set the flap outboard end blade-seal. (Ref. Fig. 405/TASK 27-54-62-991-016)
(a) Make sure that the dimension B is 33.4 mm (1.34 in.) +/- 6 mm
(0.24 in.).
(b)
Loosen the screws (126).
(c)
Adjust the blade-seal (124) until the dimension C is 8 mm (0.35 in.).
(d)
Tighten the screws (126) so that the blade-seal (124) is compressed but not out of shape.
(e)
Apply a bead of the SEALANTS (Material No. 09-002) between the cap strip (125) and the outboard flap structure.
(2)
Measure and if necessary, adjust the inboard cruise roller. (Ref. Fig. 406/TASK 27-54-62-991-013)
(a) Measure the dimension Y:
1_ If the dimension Y is between 1 mm (0.04 in.) and 2 mm (0.08
in.), the position of the cruise roller is correct. A
dimension of less than 1 mm (0.04 in.) is not permitted.
2_ If the dimension Y is more than 2 mm (0.08 in.), you must
adjust the inboard cruise roller.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-62Page 428 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(3)
To adjust the inboard cruise roller:
(a)
Remove the nut (98), the collar (97) and the serrated plate (99).
(b)
Turn the eccentric (100) until the dimension Y is correct.
(c)
Install the serrated plate (99) to lock the eccentric (100).
(d)
Install the collar (97) and the nut (98).
(e)
TORQUE the nut (98) to between 2.4 and 2.7 m.daN (17.69 and 19.91 lbf.ft).
(f)
Do a check of the dimension Y again.
(4)
If the flap guide-roller assembly was removed, install it (Ref. TASK 27-54-63-400-001).
R **ON A/C 002-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 27-54-62-820-052-A
Q. Adjustment of the Blade Seal and Cruise Roller
(1) Set the flap outboard end blade-seal.
(Ref. Fig. 405/TASK 27-54-62-991-016)
(a) Make sure that the dimension B is 33.4 mm (1.34 in.) +/- 6 mm
(0.24 in.).
(b)
Loosen the screws (126).
(c)
Adjust the blade-seal (124) until the dimension C is 8 mm (0.35 in.).
(d)
Tighten the screws (126) so that the blade-seal (124) is compressed but not out of shape.
(e)
Apply a bead of the SEALANTS (Material No. 09-002) between the cap strip (125) and the outboard flap structure.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-62Page 429 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(2) Measure and if necessary, adjust the inboard cruise roller. (Ref. Fig. 406/TASK 27-54-62-991-013)
(a) Measure the dimension Y: 1 If the dimension Y is between zero and 2 mm (0.08 in.), the
_ position of the cruise roller is correct.
2 If the dimension Y is more than 2 mm (0.08 in.), you must
_ adjust the inboard cruise roller.
(3)
To adjust the inboard cruise roller:
(a)
Remove the nut (98), the collar (97) and the serrated plate (99).
(b)
Turn the eccentric (100) until the dimension Y is correct.
(c)
Install the serrated plate (99) to lock the eccentric (100).
(d)
Install the collar (97) and the nut (98).
(e)
TORQUE the nut (98) to between 2.4 and 2.7 m.daN (17.69 and 19.91 lbf.ft).
(f)
Do a check of the dimension Y again.
(4)
If the flap guide-roller assembly was removed, install it (Ref. TASK 27-54-63-400-001).
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊(cè) AMM FLIGHT CONTROLS 飛行操縱6(65)
