(f) Install the rear pin (83) and lock with the knurled screw (84).
(2) Install the hoisting sling (Ref. TASK 27-50-00-400-002). CAUTION : OPERATE THE HOIST SLOWLY, WHEN YOU PUT THE SLING IN
_______ TENSION. DO NOT TRY TO REMOVE THE FLAP BECAUSE THIS WILL CAUSE DAMAGE.
(a) Use the hoist to carefully lift the hoisting sling until it holds the weight of the inboard flap.
Subtask 27-54-61-860-054
G. Aircraft Maintenance Configuration
(1)
Fully extend and lock the spoilers 1 and 2 (Ref. TASK 27-60-00-866-002).
(2)
Put the COLLAR-SAFETY, SPOILER on the applicable rod of the servo control.
4. Procedure
_________
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 27-54-61-020-055-A
A. Removal of the Inboard Double-Slotted Flap
(1) Disconnect the flap drive arms (106) from the rotary actuator drive-levers (110) at the track 1 and the track 2 positions. (Ref. Fig. 421/TASK 27-54-61-991-021)
CAUTION : SUPPORT THE FLAP ALONG THE FULL LENGTH OF THE TRAILING
_______ EDGE. THIS WILL PREVENT DAMAGE TO THE FLAP.
NOTE : The weight of the inboard flap is 201kgs (442lbs).
____
(a)
Remove the nut (103), the bolt (100), the washer (101) and disconnect the bonding strap (102).
(b)
Remove and discard the cotter pins (109).
1EFF : 301-399, 1 27-54-61Page A409 1 1 Aug 01/05R 1 1 1CES 1
Flap to Rotary Actuator Drive-Lever Connection
Figure 421/TASK 27-54-61-991-021
1EFF : 301-399, 1 27-54-61Page A410 1 1 Aug 01/05R 1 1 1CES 1
(c) Remove the nuts (108), the washers (107) and the bolts (104).
(2)
Carefully let the inboard flap move aft until the flap track 2 carriage touches the end stop (130). (Ref. Fig. 422/TASK 27-54-61-991-018)
(3)
Disconnect the inboard flap from the flap track 2 carriage. (Ref. Fig. 422/TASK 27-54-61-991-018)
(a)
Remove and discard the lockwire from the bolt (128).
(b)
Remove the bolt (128) and disconnect the bonding strap (129).
(c)
Remove and discard the cotter pin (125).
(d)
Remove the nut (124).
(e)
Remove and discard the crushable washer (123).
(f)
Remove the nut (126), the washer (127) and the locking plate (122).
(g)
Remove and discard the lockwire from the nuts (133).
(h)
Loosen the nuts (133) sufficiently to let the failsafe hook assembly (134) move.
(i)
Install the EXTRACTOR - PIN TRACKS 2 AND 3 (98D27504083000) to the carriage bolt (132). (Ref. Fig. 423/TASK 27-54-61-991-015)
NOTE : Make sure that you screw the extractor tool fully on to
____
the threads.
(j)
Remove the carriage bolt (132). NOTE : If necessary, carefully lift the flap with the hoist and
____ sling sufficiently to release the weight off the bolt (132).
(k)
Remove the splined bush (121).
(4) Disconnect the electrical cable connectors (144) and (145) from the connectors (143) and (146) on the track 2 beam assembly. (Ref. Fig. 424/TASK 27-54-61-991-020)
(a) Put blanking caps on the disconnected electrical connectors.
1EFF : 301-399, 1 27-54-61Page A411 1 1 Aug 01/05R 1 1 1CES 1
Flap to Flap Carriage Connection (Track 2)
Figure 422/TASK 27-54-61-991-018
1EFF : 301-399, 1 27-54-61Page A412 1 1 Aug 01/05R 1 1 1CES 1
Flap Removal and Installation Tools
Figure 423/TASK 27-54-61-991-015
1EFF : 301-399, 1 27-54-61 Page A413
1 1 Aug 01/05
1R 1
1CES 1
Details of the Flap Disconnect Cables
Figure 424/TASK 27-54-61-991-020
1EFF : 301-399, 1 27-54-61 Page A414
1 1 Aug 01/05
1R 1
1CES 1
(b) Hold the disconnected electrical cables to the flap with adhesive tape.
(5)
Disconnect the inboard flap from the flap track 1 carriage. (Ref. Fig. 425/TASK 27-54-61-991-022-A)
(a)
Remove the nut (166), the bolt (168) and disconnect the bonding strap (167) from the carriage (169).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱6(44)
