-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | C | 15.966 | 15.984 | | | 15.939 | | | | OD 23 |(0.6285) |(0.6292) | | |(0.6275) | | | | | | | 0.022 | 0.058 | | | 0.112 | | | | | (0.0008)| (0.0022)| | |(0.0044)| | C | 16.006 | 16.024 | | | | 16.051 | | | ID 20 |(0.6301) |(0.6308) | | | |(0.6319) | | -------------------------------------------------------------------------------
Subtask 27-84-62-220-126
CD. Dimensional Check of Slat 5, Track 12
(1) Fits and clearance dimensions
NOTE : The limits on the chrome-plated surfaces only apply when there
____ is a layer of chrome on the bearing surfaces.
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | C | 9.497 | 9.512 | | | 9.478 | | | | OD 25 |(0.3738) |(0.3744) | | |(0.3731) | | | | | | | 0.013 | 0.043 | | | 0.081 | | | | | (0.0005)| (0.0016)| | |(0.0031)| | C | 9.525 | 9.540 | | | | 9.559 | | | ID 21 |(0.3750) |(0.3755) | | | |(0.3763) | | -------------------------------------------------------------------------------
1EFF : ALL 1 27-84-62Page 667 1 1 Feb 01/01R 1 1 1CES 1
5. Close-up
________
Subtask 27-84-62-410-053
A. Close Access
(1) Make sure that the parts retained from the removed component are clean and in the correct condition.
(2) For the Slat track 5,
**ON A/C 001-049, 051-061, 101-105, 201-203,
(Ref. Fig. 601/TASK 27-84-62-991-008) R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 601A/TASK 27-84-62-991-008-A)
**ON A/C ALL
apply a layer of COMMON GREASE (Material No. 04-024) to:
-
the bolts (15) and (18)
-
the eccentric bush (14)
-
the bearing (9).
(3) For the Slat track 5
(a)
Put the bolt (18) in the link (10) and install the links (8) and (10).
(b)
Install the eccentric bush (14), the bolt (15), the washer (6) and the nut (7). Tighten the nut (7) with your hand (this will be safetied when the Slat No. 2 is installed).
NOTE : The bolts (1) and (19) and their related nuts and washers
____ will be correctly installed when the Slat No. 2 is installed.
(4)
For the Slat track 6, (Ref. Fig. 602/TASK 27-84-62-991-009) apply a layer of COMMON GREASE (Material No. 04-024) to:
-
the bolts (4), (18) and (20)
-
the eccentric bush (5)
-
the bearings (10) and (17).
(5)
For the Slat track 6
(a)
Put the bolt (20) in the link (9) and install the links (9) and (11).
(b)
Install the eccentric bush (5), the bolt (4), the washer (12) and the nut (13). Tighten the nut (13) with your hand (this will be safetied when the Slat No. 2 is installed).
(c)
Install the two links (16), the bolts (18), the washers (14) and the nuts (15). Tighten the nuts (15) with your hand (these will be safetied when the Slat No. 2 is installed).
NOTE : The bolts (3) and their related nuts and washers will be
____ correctly installed when the Slat No. 2 is installed.
(6)
For the Slat track 7, (Ref. Fig. 603/TASK 27-84-62-991-010) apply a layer of COMMON GREASE (Material No. 04-024) to:
-
the bolts (12) and (15)
-
the eccentric bush (6)
-
the bearing (13).
(7)
For the Slat track 7
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱8(110)
