(Ref. Fig. 401/TASK 27-84-64-991-002) R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 27-84-64-991-002-A)
**ON A/C ALL
(Ref. Fig. 402/TASK 27-84-64-991-003, 403/TASK 27-84-64-991-001)
(1)
Lift the slat into position.
(2)
At the Nos. 5 and 6 slat tracks:
(a)
Install the bush (26) in the slat.
(b)
Attach the slat to the slat tracks, and the slat track links with:
-
the bolts (27), (30), (41) and (42)
-
the washers (21), (25), (48) and (50)
-
the nuts (22), (24), (49) and (51).
NOTE : If necessary, turn the eccentric bushes (31) and (46) to
____ install the bolts (27), (30), (41) and (42).
(c) TORQUE the nuts (22), (24), (49), (51), (55) and (56) to between
1.95 and 2.2 m.daN (14.38 and 16.22 lbf.ft).
(d)
Safety the nuts (22), (24), (49), (51), (55) and (56) with the new cotter pins (23).
(e)
Do not torque or safety the nuts (32) and (47).
(3)
Remove the SLING-SLATS (Ref. TASK 27-80-00-000-001).
(4)
You must adjust the upper trailing-edge of the slat to its maximum height, related to the fixed leading-edge. To adjust the height, turn the eccentric bushes (31) and (46) on the No. 5 and 6 slat tracks.
Subtask 27-84-64-820-055
C. Adjustment of the Slat
**ON A/C 001-049, 051-061, 101-105, 201-203,
(Ref. Fig. 401/TASK 27-84-64-991-002) R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 27-84-64-991-002-A)
**ON A/C ALL
(Ref. Fig. 402/TASK 27-84-64-991-003, 403/TASK 27-84-64-991-001, 404/TASK 27-84-64-991-004)
(1)
Install the BLOCK-SLAT GAPPING (98D27804020000) at the No. 9 slat track.
(2)
Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT, installed outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-000-003).
(3)
Use the ADAPTOR-DRIVE, SLAT (AND FLAP) (98D27804001000) to retract the slats until they are approximately 50.8 mm (2.0000 in.) +/- 6.35 mm (0.2500 in.) from the BLOCK-SLAT GAPPING.
(4)
Use the BAR-TURNING (98D27804011000) to slowly retract the slats until the BLOCK-SLAT GAPPING touches the bottom roller at the No. 9 slat track.
(5)
Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-400-003).
(6)
Adjust the eccentric bushes (31) and (46) at the No. 5 and 6 slat tracks to get dimension L. Refer to the table that follows.
NOTE : Measure dimension L above the applicable slat track.
____
-------------------------------------------------------------------------------| TRACK | DIMENSION L | MAXIMUM ADJUSTMENT BECAUSE OF | | NOS. | | LOCKING PLATE INSTALLATION | -------------------------------------------------------------------------------| 5 and 6 | 4.00 mm (0.1575 in.) | +0.25 mm (0.01 in.) -0.25 mm (0.01 in.) | -------------------------------------------------------------------------------
(7)
Install the locking plates (28) and (43) and the nuts (29) and (44).
(8)
TORQUE the nuts (32) and (47) to between 1.95 and 2.2 m.daN (14.38 and 16.22 lbf.ft).
(9)
Safety the nuts (32) and (47) with the new cotter pins (23).
(10)
Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT, installed outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-000-003).
(11)
Use the pneumatic wrench and the ADAPTOR-DRIVE, SLAT (AND FLAP) to fully extend the slats.
1EFF : ALL 1 27-84-64Page 421 1 1 Nov 01/03R 1 1 1CES 1
(12)
Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-400-003).
(13)
Apply special materials:
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(a) Apply SEALANTS (Material No. 09-001) to:
-
the nuts (22), (24), (32), (47), (49), (51), (55) and (56)
-
the bolt heads (18), (27), (30), (41), (42), (45), (53) and
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱8(129)
