27-84-63-991-001  Fig. 401
 **ON A/C 001-049, 051-061, 101-105, 201-203,
 27-84-63-991-002  Fig. 402
R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
 27-84-63-991-002-A  Fig. 402A
 **ON A/C ALL
 27-84-63-991-003  Fig. 403

 3. Job Set-up__________ 
R
 Subtask 27-84-63-941-050
 A. Safety Precautions
 (1) Put the safety barriers in position. 
R 
R  (2) Fully retract the slats (Ref. TASK 27-80-00-866-005). 
R  (3) Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) 
R  on the flap/slat control lever on panel 114VU. 
R  (4) Put a warning notice in the cockpit to tell persons not to operate 
R  the slat controls.
 Subtask 27-84-63-860-054 
R  B. Aircraft Maintenance Configuration 
R  (1) Energize the ground service network 
R  (Ref. TASK 24-42-00-861-001). 
R  (2) On the MCDU: 
R  (a) Get access to the SYSTEM REPORT/TEST F/CTL page (Ref. TASK 31-32-
R  00-860-006). 
R  -------------------------------------------------------------------------------
R  ACTION RESULT 
R  -------------------------------------------------------------------------------

R  1. On MCDU:  On the MCDU: 
R  - push the line key for <SFCC1  - the MCDU shows the SFCC1 menu page 1. 
R 
R  2. Push the NEXT PAGE button  - the MCDU shows the SFCC1 menu page 2. 
R 
R  3. Push the line key (2L) SYSTEM  - the MCDU shows the slat SYSTEM DATA 
R  DATA SLT>  submenu.

R  -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
R  4. Push the line key (1L) <PPU  - the MCDU shows the PPU DATA page(s). 
R R R R  5. Write down the APPU and the FPPU angles (deg) shown on the display or push (in) the line key PRINT > to get a print out of the screen. 
R R  (3) De-energize the ground service network (Ref. TASK 24-42-00-862-001). 
R R (4) Remove the safety collar from the circuit breakers 9CV and 11CV. 
Subtask 27-84-63-865-050 
R  C. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/WTB/SLT/SYS2 11CV P19 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21 122VU FLIGHT CONTROLS/WTB/SLT/SYS1 9CV S06
 Subtask 27-84-63-010-051 
R  D. Get Access 
R  (1) Put the adjustable access platform below the zone 510(610). 
R R R  (2) Remove the applicable access panel (Ref. TASK 57-41-37-000-006): - for the left wing, remove 522NB - for the right wing, remove 622NB. 
R  (3) Remove the applicable torque shaft (Ref. TASK 27-84-45-000-004): - for the left wing, remove FIN 6010CM - for the right wing, remove FIN 6060CM. 
R  (4) Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT, installed outboard of the removed torque shaft FIN 6010CM (6060CM) (Ref. TASK 27-50-00-000-003). 

R 1EFF : ALL 1 27-84-63Page 404 1 1 Nov 01/03 1 1 1CES 1

 (5) Install the ADAPTOR-DRIVE, SLAT (AND FLAP) (98D27804001000) and a pneumatic wrench or a wrench and socket on the applicable bevel gearbox:
 -
for the left wing, use FIN 6010CM

 -
for the right wing, use FIN 6060CM.
 NOTE : This will let you operate the slats manually.

____
 (6)
 Manually extend the slats to the fully extended position

 (7)
 Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-400-003).

 (8) Remove the slat track closing plates (Ref. TASK 27-84-69-000-001). Subtask 27-84-63-480-051
 E. Installation of Support Equipment
 (1) Install the SLING-SLATS (98D27804009001) (Ref. TASK 27-80-00-400-001).
 4. Procedure
_________
 (Ref. Fig. 401/TASK 27-84-63-991-001)
 **ON A/C 001-049, 051-061, 101-105, 201-203,
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱8(114)