(a)
 Push the upper trailing edge of the slat down with a hand force of 25 kg (55.1155 lb). Put the load, at each track position, at the trailing edge of the slat. Measure and write down the dimension X.

 (b)
 Pull the upper trailing edge of the slat up with a hand force of 25 kg (55.1155 lb). Put the load, at each track position, at the trailing edge of the slat. Measure and write down the dimension X again.

 (c)
 Subtract the smaller dimension X from the larger dimension X to give you the surface-attachment spherical-bearing backlash. The difference between the two dimensions, that you wrote down, must be no more than 2.0 mm (0.0787 in.).

 (2)
 For dimension Y (tracks 5 thru 12), to check the slat track drive system backlash:

 (a)
 Push the applicable track with a hand force of 25 kg (55.1155 lb) aft. Measure and write down the dimension Y.

 (b)
 Pull the applicable track with a hand force of 25 kg (55.1155 lb) forward. Measure and write down the dimension Y again.

 (c)
 Subtract the smaller dimension Y from the larger dimension Y to give you the rotary-actuator/transmission-shafts backlash. The difference between the two dimensions, that you wrote down, must be no more than 2.5 mm (0.0984 in.).

 Slat 2, 3, 4 and 5 - Trailing Edge Backlash Figure 609A/TASK 27-84-62-991-016-A
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-84-62Page 678 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 5. Close-up
________ Subtask 27-84-62-860-054
 A. Aircraft Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 (1) Retract the slats fully (Ref. TASK 27-80-00-866-005). Subtask 27-84-62-942-052
 B. Removal of Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the safety barriers.

 (3)
 Remove the warning notice(s).

 (4)
 Remove the access platform(s).

 (5)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 SLAT 1 - REMOVAL/INSTALLATION_____________________________
 TASK 27-84-63-000-001
 Removal of the No. 1 Slat
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR. 
R R R  WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR._______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 1. Reason for the Job__________________
 Self Explanatory
 2. Job Set-up Information______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R R  No specific No specific No specific No specific No specific No specific No specific 98D27803500001 98D27804001000  circuit breaker(s) safety clip(s)pneumatic wrenchsafety barrierssupport strut warning noticewrench and socketadjustable access platform 3.5 m (11 ft. 6 in.) 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER1 ADAPTOR-DRIVE, SLAT (AND FLAP)

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power 27-50-00-000-003 Removal of the Lock-Torque Shaft - Flaps and Slats (98D27504030001) 27-50-00-400-003 Installation of the Lock-Torque Shaft - Flaps and
 Slats (98D27504030001) 27-80-00-000-001 Removal of the Hoisting Sling 27-80-00-400-001 Installation of the Hoisting Sling 27-80-00-866-005 Retracting the Slats on the Ground 27-84-45-000-004 Removal of the Torque Shaft 6010CM(6060CM) 27-84-69-000-001 Removal of the Closing Plates for the Slat Tracks 1
 thru 12 31-32-00-860-006 Procedure to Get Access to the SYSTEM REPORT/TEST F/CTL Page
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱8(113)