(c)
 Install the links (8) and (31), the bolt (29), the washer (13) and the nut (14).

 (d)
 Install the bolt (30), the washer (10) and the nut (11). Tighten the nuts (14) and (11) with your hand (these will be safetied when the Slat No. 5 is installed).

 NOTE : The bolts (5) and (6) and their related nuts and washers
____ will be correctly installed when the Slat No. 5 is installed.
 (18)
 Install the applicable Slat track (Ref. TASK 27-84-62-400-001).

 (19)
 Install the applicable Slat:

 -
for Slat tracks 5 and 6, install Slat No. 2 (Ref. TASK 27-84-64-400-002)

 -
for Slat tracks 7 and 8, install Slat No. 3 (Ref. TASK 27-84-65-400-002)

 -
for Slat tracks 9 and 10, install Slat No. 4 (Ref. TASK 27-84-66-400-002)

 -
for Slat tracks 11 and 12, install Slat No. 5 (Ref. TASK 27-84-67-400-002).

 Subtask 27-84-62-942-053
 B. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Make sure that the work area is clean and clear of tool(s) and other items.

 1EFF : ALL 1 27-84-62Page 672 1 1 Feb 01/01R 1 1 1CES 1

 (3)
 Remove the warning notice(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 27-84-62Page 673 1 1 Feb 01/01R 1 1 1CES 1

 TASK 27-84-62-200-002 Check of Slat 2, 3, 4 and 5 Trailing Edge Backlash WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
 No specific warning notice
 No specific adjustable access platform 3.5 m (11 ft. 6 in.)
 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-80-00-866-004 Extending the Slats on the Ground
 27-80-00-866-005 Retracting the Slats on the Ground

R **ON A/C 001-049, 051-061, 101-105, 201-203,
 27-84-62-991-016 Fig. 609 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
 27-84-62-991-016-A Fig. 609A
 **ON A/C ALL

 3. Job Set-up
__________
 Subtask 27-84-62-941-050

 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 Put a warning notice in the cockpit to tell persons not to operate the slat controls.

 Subtask 27-84-62-860-050
 B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 (1)
 Extend the slats fully (Ref. TASK 27-80-00-866-004).

 (2)
 Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) is installed on the slat/flap control lever.

 (3)
 Put the adjustable access platform below the work area.

 4. Procedure
_________
 **ON A/C 001-049, 051-061, 101-105, 201-203,

 (Ref. Fig. 609/TASK 27-84-62-991-016)

 Slat 2, 3, 4 and 5 - Trailing Edge Backlash
 Figure 609/TASK 27-84-62-991-016

R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 27-84-62Page 676 1 1 May 01/05 1 1 1CES 1R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,

 (Ref. Fig. 609A/TASK 27-84-62-991-016-A)
 **ON A/C ALL
 Subtask 27-84-62-220-142
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱8(112)