-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice(s)
No specific access platform 3.5 m (11 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-80-00-866-004 Extending the Slats on the Ground 27-84-44-000-003 Removal of the Steady Bearing FIN 6021CM(6071CM) 27-84-45-991-001 Fig. 401 27-84-45-991-003 Fig. 403
3. Job Set-up
__________ (Ref. Fig. 401/TASK 27-84-45-991-001, 403/TASK 27-84-45-991-003) Subtask 27-84-45-941-076
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put the warning notice(s) in position to tell persons not to operate the slat controls.
Subtask 27-84-45-865-101
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
Subtask 27-84-45-860-050
C. Aircraft Maintenance Configuration
(1)
Extend the slats fully (Ref. TASK 27-80-00-866-004).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is on the slat/flap control lever.
(3)
Remove the applicable steady bearing (43) (Ref. TASK 27-84-44-000-003):
-
FOR 6022CM
remove the steady bearing FIN 6021CM
-
FOR 6072CM
remove the steady bearing FIN 6071CM.
1EFF : ALL 1 27-84-45Page 479 1 1 Feb 01/00R 1 1 1CES 1
Subtask 27-84-45-010-056
D. Get Access
(1)
Put an access platform in position below the applicable access panel 521AT (621AT).
(2)
Remove the applicable access panel:
-
FOR 6022CM
remove 521AT
-
FOR 6072CM
remove 621AT.
4. Procedure
_________
(Ref. Fig. 403/TASK 27-84-45-991-003) Subtask 27-84-45-020-058
A. Removal of the Torque Shafts 6022CM(6072CM)
(1) Remove the nuts (40), the bolts (41) and the shaft (42).
1EFF : ALL 1 27-84-45Page 480 1 1 Feb 01/00R 1 1 1CES 1
TASK 27-84-45-400-010
Installation of the Torque Shaft 6022CM(6072CM)
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
R R Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-018
GENERAL PURPOSE ASSEMBLY PASTE (Ref. 20-31-00)
Material No. 04-022 USA MIL-PRF-81322 GRADE 2
SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 15-007 AIB TN 10138 TYPE II GRADE 1 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00) 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱8(6)
