R 3. Job Set-up__________
R Subtask 57-51-37-941-061
R A. Safety Precautions
R (1) Put the safety barriers in position.
R (2) Make sure that the flaps/slats are fully retracted (Ref. TASK 27-50-
R 00-866-009).
R (3) Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001)
R on the flap/slat control lever.
R (4) Put the warning notices in the cockpit to tell persons not to operate
R the flaps or slats.
R Subtask 57-51-37-010-057
R B. Get Access
R (1) Put the adjustable access platform below the applicable access panel,
R zone 575(675).
R 4. Procedure_________
R (Ref. Fig. 408/TASK 57-51-37-991-007)
R Subtask 57-51-37-020-055
R A. Removal of the Access Panel 575AT(675AT)
R (1) Remove the nineteen bolts (2) then remove the access panel (1).
R R Upper Trailing Edge Access Panel 575AT(675AT) Figure 408/TASK 57-51-37-991-007- 12 (SHEET 1)
1EFF : 1 1 1CES ALL 1 111 57-51-37 Page 464 May 01/05
R R Upper Trailing Edge Access Panel 575AT(675AT) Figure 408/TASK 57-51-37-991-007- 22 (SHEET 2)
1EFF : 1 1 1CES ALL 1 111 57-51-37 Page 465 May 01/05
R TASK 57-51-37-400-007
R Installation of the Access Panel 575AT(675AT)
R WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______
R GEAR.
R WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______
R START A TASK ON OR NEAR:
R - THE FLIGHT CONTROLS
R - THE FLIGHT CONTROL SURFACES
R - THE LANDING GEAR AND THE RELATED DOORS
R - COMPONENTS THAT MOVE.
R CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______
R - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
R - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
R - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY.
R INCORRECT INSTALLATION CAN CAUSE DAMAGE.
R 1. Reason for the Job__________________
R Self Explanatory
R 2. Job Set-up Information______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific safety barriers
R No specific warning notices
R No specific adjustable access platform 4.0 m (13 ft. 1 in.)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
R B. Consumable Materials
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R Material No. 09-016 USA MIL-PRF-81733D TYPE II CLASS B
R CORROSION INHIBITING FILLET CONSISTENCY
R (Ref. 20-31-00)
R Material No. 11-026 GB DEF-STAN 68-148/1
R SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
R Material No. 19-003 USA AMS 3819
R LINT-FREE COTTON CLOTH (Ref. 20-31-00)
R C. Referenced Information
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R 57-51-37-991-007 Fig. 408
R 3. Job Set-up__________
R Subtask 57-51-37-941-060
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(10)
