(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control lever.
(3)
Do a manual extension of the spoilers (Ref. TASK 27-60-00-866-002).
1EFF : ALL 1 57-53-00Page A605 1 1 May 01/05R 1 1 1CES 1
(4)
Make sure that the COLLAR-SAFETY, SPOILER is installed on the applicable spoiler actuator.
(5)
Put the access platform below the applicable wing trailing edge at flap tracks 3 and 4, zones 532(632) and 533(633).
Subtask 57-53-00-865-083
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
4. Procedure
_________ (Ref. Fig. 616/TASK 57-53-00-991-017) CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 57-53-00-110-063
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the drive lever.
Subtask 57-53-00-280-056
B. Inspection
(1) Do a special detailed inspection of the drive levers on flap tracks 3 and 4 (Ref. NTM 57-53-54 PART 6).
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575300) for the
____ correct repair procedure. If the defect is not in this repair, you must request a procedure from Airbus Industrie.
1EFF : ALL 1 57-53-00Page A606 1 1 May 01/05R 1 1 1CES 1
Outboard Flap Tracks 3 and 4 - Drive Levers - Location
Figure 616/TASK 57-53-00-991-017
1EFF : ALL 1 57-53-00Page A607 1 1 May 01/05R 1 1 1CES 1
5. Close-up
________ Subtask 57-53-00-865-084
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-53-00-860-099
B. Aircraft Maintenance Configuration
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Do a manual retraction of the spoilers (Ref. TASK 27-60-00-866-002).
(3) Fully retract the flaps (Ref. TASK 27-50-00-866-009). Subtask 57-53-00-942-066
C. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-53-00Page A608 1 1 May 01/05R 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-214,
TASK 57-53-00-220-009
R Special Detailed Inspection of Outboard Flap, Front Spar Splices and Attachment R Areas at Track 4, Internal and External, LH/RH
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575305-02
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(93)
