R C. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R 27-50-00-866-008 Extension of the Flaps on the Ground
R 27-50-00-866-009 Retraction of the Flaps on the Ground
R NTM 575239 PART 9
R ASRM 575200 (for corrective action)
R 57-52-00-991-026 Fig. 626
R 3. Job Set-up__________
R Subtask 57-52-00-941-079
R A. Safety Precautions
R (1) Put a warning notice on the flap/slat control lever (panel 114VU) to
R tell persons not to operate the flaps.
R (2) Put the safety barriers in position.
R Subtask 57-52-00-860-073
R B. Aircraft Maintenance Configuration
R WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE_______
R CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS
R AND/OR DAMAGE.
R (1) Fully extend the flaps (Ref. TASK 27-50-00-866-008).
R (2) Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is
R installed on the flap/slat control lever on the panel 114VU.
R Subtask 57-52-00-865-107
R C. Open, safety and tag this(these) circuit breaker(s):
R -------------------------------------------------------------------------------
R PANEL DESIGNATION IDENT. LOCATION
R -------------------------------------------------------------------------------
R 49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07
R 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
R Subtask 57-52-00-010-077
R D. Get Access
R (1) Put the access platform in position below the inboard flap at zone
R 581(681).
R (2) Remove and discard the covers to the inspection holes in the bottom
R skin each side of Rib 3.
R (3) Make sure that the applicable inspection holes are clear of unwanted
R material.
R 4. Procedure_________
R (Ref. Fig. 626/TASK 57-52-00-991-026)
R CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING_______
R EDGE:
R - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
R - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
R - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY.
R INCORRECT INSTALLATION CAN CAUSE DAMAGE.
R Subtask 57-52-00-280-060
R A. Inspection
R (1) Do a special detailed inspection of Rib 3 of the inboard double
R slotted flap LH/RH (Ref. NTM 575239 PART 9).
R NOTE : If necessary, refer to the ASRM (Ref. ASRM 575200) for the____
R correct repair procedure. If the defect is not included in
R this repair, you must request a procedure from Airbus
R Industrie.
R 5. Close-up________
R Subtask 57-52-00-410-079
R A. Close Access
R (1) Make sure that the work area is clean and clear of tool(s) and other
R items.
R (2) Use BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061A), cut to the
R correct dimensions, to make new covers for the inspection holes.
R Inboard Flap - Rib 3 - Inspection Area
R Figure 626/TASK 57-52-00-991-026- 12 (SHEET 1)
1EFF : 301-399, 1 57-52-00Page A652 1 1 May 01/04 1 1 1CES 1
R Inboard Flap - Rib 3 - Inspection Area
R Figure 626/TASK 57-52-00-991-026- 22 (SHEET 2)
1EFF : 301-399, 1 57-52-00Page A653 1 1 May 01/04 1 1 1CES 1
R (3) Install the new covers on the inspection holes.
R Subtask 57-52-00-865-108
R B. Remove the safety clip(s) and the tag(s) and close this(these) circuit
R breaker(s):
R 6CV, 8CV.
R Subtask 57-52-00-860-074
R C. Aircraft Maintenance Configuration
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護(hù)手冊 AMM WINGS 機翼4(51)
