曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  D. Get Access 
R  (1) Put the access platform in position below the tab hinge-fairing at 
R  zone 535(635). 
R  (2) Remove the applicable inboard flap tab hinge-fairing at Rib 3 
R  (Ref. TASK 57-55-11-000-005): 
R  - for the left wing, remove 535AB, 535BB 
R  - for the right wing, remove 635AB, 635BB. 
R  (3) Put the spark-proof lamp adjacent to the inspection area. 
R  4. Procedure_________ 
R  (Ref. Fig. 623/TASK 57-52-00-991-023) 
R  CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING_______ 
R  EDGE: 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. 
R  - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. 
R  INCORRECT INSTALLATION CAN CAUSE DAMAGE. 
R  Subtask 57-52-00-210-064 
R  A. Detailed Visual Inspection of Inboard Double Slotted Flap, Tab Drive 
R  Assembly and Articulation at Rib 3, LH/RH 
R  (1) Do an inspection of the control rod, the drive rods, the support rod 
R  and the tab links. Make sure that: 
R  - there is no damage 
R  - there is no corrosion 
R  - there are no cracks or scores 
R  - the inboard double slotted flap, tab drive assembly and 
R  articulation are correctly installed.

 

R Inboard Flap - Tab Drive Assembly and Articulation at Rib 3 - Inspection Area R Figure 623/TASK 57-52-00-991-023
 1EFF : 301-399, 1 57-52-00Page A635 1 1 May 01/04 1 1 1CES 1

R  (2) Do an inspection of the forward and middle levers, the front and aft 
R  flap brackets, the tab joining, tab leader ship and the bracket. Make 
R  sure that: 
R  - there is no damage 
R  - there is no corrosion 
R  - there are no cracks or scores 
R  - the surface protection is in the correct condition. 
R  NOTE : If necessary, refer to the ASRM (Ref. ASRM 575200) for the____ 
R  correct repair procedure. 
R  5. Close-up________ 
R  Subtask 57-52-00-410-076 
R  A. Close Access 
R  (1) Remove the spark-proof lamp from the inspection area. 
R  (2) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (3) Install the applicable inboard flap tab hinge-fairing (Ref. TASK 57-
R  55-11-400-005): 
R  - for the left wing, install 535AB, 535BB 
R  - for the right wing, install 635AB, 635BB. 
R  Subtask 57-52-00-865-102 
R  B. Remove the safety clip(s) and the tag(s) and close this(these) circuit 
R  breaker(s): 
R  6CV, 8CV. 
R  Subtask 57-52-00-860-068 
R  C. Aircraft Maintenance Configuration 
R  (1) Fully retract the flaps (Ref. TASK 27-50-00-866-009). 
R  Subtask 57-52-00-942-075 
R  D. Removal of Equipment 
R  (1) Remove the access platform(s). 
R  (2) Remove the safety barriers.

 

R (3) Remove the warning notice(s).
R (4) Remove the ground support and maintenance equipment, the special and R standard tools and all other items.

R  TASK 57-52-00-210-007 
R  Detailed Visual Inspection of Inboard Double Slotted Flap, Tab Articulation at 
R  RIB6, LH/RH 
R  WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ 
R  START A TASK ON OR NEAR: 
R  - THE FLIGHT CONTROLS 
R  - THE FLIGHT CONTROL SURFACES 
R  - THE LANDING GEAR AND THE RELATED DOORS 
R  - COMPONENTS THAT MOVE. 
R  WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ 
R  GEAR. 
R  CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______ 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. 
R  - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. 
R  INCORRECT INSTALLATION CAN CAUSE DAMAGE. 
R  1. Reason for the Job__________________ 
R  Refer to the MPD TASK: 575235-01 
R  2. Job Set-up Information______________________ 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(47)