-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575309-02
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notices No specific access platform 2.5 m (8 ft. 2 in.) 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-061A D DAN 220 ALUMINIUM FOIL ADHESIVE TAPE (Ref. 20-31-00)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 642 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 27-54-62-000-003 Removal of the Leading Edge Panels 2 and 5 on the
Outboard Flap 27-54-62-400-003 Installation of the Leading Edge Panels 2 and 5 on
the Outboard Flap 57-55-11-000-001 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-400-001 Installation of the Flap Track Fairings Nos. 2, 3 and
4
NTM 57-53-09 PART 9
ASRM 575300 (for corrective action)
**ON A/C 001-049, 051-056,
57-53-00-991-008 Fig. 607
R **ON A/C 057-099, 101-149, 151-199, 201-299, 401-499,
57-53-00-991-008-A Fig. 607A
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
3. Job Set-up
__________
Subtask 57-53-00-941-057
A. Safety Precautions
(1)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(2)
Put the safety barriers in position.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 643 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Subtask 57-53-00-860-106
B. Aircraft Maintenance Configuration
(1)
Extend the flaps fully (Ref. TASK 27-50-00-866-008).
(2)
Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) on the flap/slat control lever.
Subtask 57-53-00-865-063
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
**ON A/C 001-049, 051-056,
Subtask 57-53-00-010-056
D. Get Access
(Ref. Fig. 607/TASK 57-53-00-991-008)
(1)
Put the access platform below the applicable wing trailing edge at flap track 3, zone 532(632).
(2)
Remove the access panel 532AT (632AT) and the flap track 3 fairing 532CB (632CB) (Ref. TASK 57-55-11-000-001).
(3)
Remove the outboard flap leading edge panel 2 (Ref. TASK 27-54-62-000-003).
(4)
Remove and discard the cover from the LH inspection hole on the front spar.
(5)
Make sure that the inspection hole is clear of unwanted material.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 644 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Outboard Flap
Figure 607/TASK 57-53-00-991-008
R 1EFF : 001-049, 051-056, 1 57-53-00Page 645 1 1 Aug 01/05 1 1 1CES 1 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(78)
