曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  (1) Put the access platform in position below the flap track 2 at zone 
R  531(631). 
R  (2) Remove the applicable flap track fairing (Ref. TASK 57-55-11-000-
R  004): 
R  - for the left wing, remove 531AT, 531CB 
R  - for the right wing, remove 631AT, 631CB. 
R  (3) Put the spark-proof lamp adjacent to the inspection area. 
R  4. Procedure_________ 
R  (Ref. Fig. 625/TASK 57-52-00-991-025) 
R  CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING_______ 
R  EDGE: 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. 
R  - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. 
R  INCORRECT INSTALLATION CAN CAUSE DAMAGE. 
R  Subtask 57-52-00-210-066 
R  A. Inspection 
R  (1) Do an inspection of the A-strut, the tab drive strut, the tab bracket 
R  and the rear link. Make sure that: 
R  - there is no damage 
R  - there is no corrosion 
R  - there are no cracks or scores 
R  - the struts and the link are attached correctly 
R  - the surface protection is in the correct condition. 
R  NOTE : If necessary, refer to the ASRM (Ref. ASRM 575200) for the____ 
R  correct repair procedure.

 

R Inboard Flap - Tab Drive Strut and Articulation at Rib 9 - Inspection Area R Figure 625/TASK 57-52-00-991-025
 1EFF : 301-399, 1 57-52-00Page A647 1 1 May 01/04 1 1 1CES 1

R  5. Close-up________ 
R  Subtask 57-52-00-410-078 
R  A. Close Access 
R  (1) Remove the spark-proof lamp from the inspection area. 
R  (2) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (3) Install the applicable flap track fairing (Ref. TASK 57-55-11-400-
R  004): 
R  - for the left wing, install 531AT, 531CB 
R  - for the right wing, install 631AT, 631CB. 
R  Subtask 57-52-00-865-106 
R  B. Remove the safety clip(s) and the tag(s) and close this(these) circuit 
R  breaker(s): 
R  6CV, 8CV. 
R  Subtask 57-52-00-860-072 
R  C. Aircraft Maintenance Configuration 
R  (1) Fully retract the flaps (Ref. TASK 27-50-00-866-009). 
R  Subtask 57-52-00-942-077 
R  D. Removal of Equipment 
R  (1) Remove the access platform(s). 
R  (2) Remove the safety barriers 
R  (3) Remove the warning notice(s). 
R  (4) Remove the ground support and maintenance equipment, the special and 
R  standard tools and all other items.

 

R  TASK 57-52-00-220-012 
R  Special Detailed Inspection of Inboard Double Slotted Flap, RIB3, LH/RH 
R  WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ 
R  START A TASK ON OR NEAR: 
R  - THE FLIGHT CONTROLS 
R  - THE FLIGHT CONTROL SURFACES 
R  - THE LANDING GEAR AND THE RELATED DOORS 
R  - COMPONENTS THAT MOVE. 
R  WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ 
R  GEAR. 
R  CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______ 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. 
R  - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. 
R  INCORRECT INSTALLATION CAN CAUSE DAMAGE. 
R  1. Reason for the Job__________________ 
R  Refer to the MPD TASK: 575239-01 
R  2. Job Set-up Information______________________ 
R  A. Fixtures, Tools, Test and Support Equipment 
R  -------------------------------------------------------------------------------
R  REFERENCE  QTY DESIGNATION 
R  -------------------------------------------------------------------------------
R  No specific  circuit breaker(s) safety clip(s) 
R  No specific  safety barriers 
R  No specific  warning notice 
R  No specific  access platform 2.5 m (8 ft. 2 in.) 
R  B. Consumable Materials 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(50)