(2)
 Install the applicable flap track 2 fairings 531AT, 631AT, 531CB, 631CB (Ref. TASK 57-55-11-400-001).

 Subtask 57-52-00-865-079
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
 Subtask 57-52-00-860-092
 C. Aircraft Configuration
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Retract the flaps (Ref. TASK 27-50-00-866-009).

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-52-00Page 674 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 57-52-00-942-064

 D. Removal of Equipment
 (1)
 Remove the access platform(s).

 (2)
 Remove the warning notice(s).

 (3)
 Remove the safety barriers.

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-52-00Page 675 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 TASK 57-52-00-220-008

 Special Detailed Inspection of the Inboard Flap, Internal Brackets at Track 2 LH/RH
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 575206-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific safety barriers
 No specific warning notices
 No specific access platform 2.5 m (8 ft. 2 in.)

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-061A  D DAN 220 ALUMINIUM FOIL ADHESIVE TAPE (Ref. 20-31-00)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-52-00Page 676 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 57-55-11-000-001 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-400-001 Installation of the Flap Track Fairings Nos. 2, 3 and
 4 NTM 57-52-06 PART 9 ASRM 575200 (for corrective action) 57-52-00-991-013 Fig. 613
 3. Job Set-up
__________ Subtask 57-52-00-941-066
 A. Safety Precautions
 (1) Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
 (2) Put the safety barriers in position. Subtask 57-52-00-860-103
 B. Aircraft Maintenance Configuration
 (1)
 Fully extend the flaps (Ref. TASK 27-50-00-866-008).

 (2)
 Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control lever.

 Subtask 57-52-00-865-080
 C. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-52-00Page 677 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 57-52-00-010-064

 D. Get Access
 (1)
 Put the access platform below the applicable wing trailing edge at flap track 2, zone 531(631).

 (2)
 Remove the access panel 531AT (631AT) and the flap track 2 fairing 531CB (631CB) (Ref. TASK 57-55-11-000-001).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(31)