R 1EFF : 301-399, 1 57-52-00Page 697 1 1 May 01/04 1 1 1CES 1R Inboard Flap - Inboard Trunnion - Inspection Area R Figure 616/TASK 57-52-00-991-016

R 1EFF : 301-399, 1 57-52-00Page 698 1 1 May 01/04 1 1 1CES 1

R  Subtask 57-52-00-280-057 
R  B. Inspection 
R  (1) Do a special detailed inspection of the trunnion attachment bracket 
R  and inboard trunnion LH/RH (Ref. NTM 57-52-23 PART 9). 
R  NOTE : If necessary, refer to the ASRM (Ref. ASRM 575200) for the____ 
R  correct repair procedure. If the defect is not included in 
R  this repair, you must request a procedure from Airbus 
R  Industrie. 
R  5. Close-up________ 
R  Subtask 57-52-00-410-069 
R  A. Close Access 
R  (1) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (2) Use BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061A) cut to the 
R  correct dimensions, to make the new covers for the inspection holes. 
R  (3) Install the new covers on the inspection holes in the lower surface 
R  of the flap. 
R  (4) Install the access panel 581AT (681AT) in the upper surface of the 
R  flap. 
R  Subtask 57-52-00-865-088 
R  B. Remove the safety clip(s) and the tag(s) and close this(these) circuit 
R  breaker(s) 6CV, 8CV. 
R  Subtask 57-52-00-860-054 
R  C. Aircraft Maintenance Configuration 
R  (1) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat 
R  control lever. 
R  (2) Retract the flaps (Ref. TASK 27-50-00-866-009).

R Subtask 57-52-00-942-068

R  D. Removal of Equipment 
R  (1) Remove the access platform(s). 
R  (2) Remove the safety barriers. 
R  (3) Remove the warning notice(s). 
R  (4) Remove the ground support and maintenance equipment, the special and 
R  standard tools and all other items.

R TASK 57-52-00-210-002

R  Detailed Visual Inspection of Inboard Double Slotted Flap, Drive Strut for Flap 
R  and Drive Lever for Flap Track Fairing, Including Attachment Brackets .... 
R  WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ 
R  START A TASK ON OR NEAR: 
R  - THE FLIGHT CONTROLS 
R  - THE FLIGHT CONTROL SURFACES 
R  - THE LANDING GEAR AND THE RELATED DOORS 
R  - COMPONENTS THAT MOVE. 
R  WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ 
R  GEAR. 
R  CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______ 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. 
R  - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. 
R  INCORRECT INSTALLATION CAN CAUSE DAMAGE. 
R  1. Reason for the Job__________________ 
R  Refer to the MPD TASK: 575225-01 
R  Detailed Visual Inspection of Inboard Double Slotted Flap, Drive Strut for 
R  Flap and Drive Lever for Flap Track Fairing, Including Attachment Bracket to 
R  the Flap at Track 2, LH/RH 
R  2. Job Set-up Information______________________ 
R  A. Fixtures, Tools, Test and Support Equipment 
R  -------------------------------------------------------------------------------
R  REFERENCE  QTY DESIGNATION 
R  -------------------------------------------------------------------------------
R  No specific  circuit breaker(s) safety clip(s) 
R  No specific  safety barriers 
R  No specific  spark-proof 
R  No specific  warning notice 
R  No specific  access platform 2.5 m (8 ft. 2 in.)

R B. Referenced Information

R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R 27-50-00-866-008 R 27-50-00-866-009 R 57-55-11-000-004 R 57-55-11-400-004 R R ASRM 575200 R 57-52-00-991-017
R 3. Job Set-up
__________
R Subtask 57-52-00-941-070
R A. Safety Precautions Extension of the Flaps on the Ground Retraction of the Flaps on the Ground Removal of the Flap Track Fairings Nos. 2, 3 and 4 Installation of the Flap Track Fairings Nos. 2, 3 and 4 (for corrective action) Fig. 617
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(37)