3. Job Set-up
__________
Subtask 57-52-21-941-051
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER is on the flap/slat control lever.
(3)
Make sure that the warning notices are in position to tell persons not to operate the flap/slat system.
Subtask 57-52-21-865-052
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-52-21-860-051
C. Aircraft Maintenance Configuration
(1)
Make sure that the access platform is below the applicable inboard flap, at zone 531(631).
(2)
Make sure that the applicable inboard flap is removed (Ref. TASK 27-54-61-000-001).
R **ON A/C 301-399,
R Subtask 57-52-21-860-051-A
R C. Aircraft Maintenance Configuration
R R (1) Make sure that the access platform is below the applicable inboard flap, at zone 531(631).
R R (2) Make sure that the applicable inboard flap is removed (Ref. TASK 27-54-61-000-003).
R **ON A/C ALL
4. Procedure_________
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING_______ EDGE: - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 57-52-21-420-052
A. Preparation for Installation.
(1) Clean the component interfaces and the adjacent areas with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(2) Do an inspection of the component interface and/or the adjacent area.
(3) Make sure that the parts retained from the removed component are clean and in the correct condition.
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-52-21-420-053
B. Installation of the Flap Attachment Bearing
(1)
Apply SPECIAL MATERIALS (Material No. 05-002) to the external surface of the new spherical bearing (7).
(2)
Make sure that the SPECIAL MATERIALS (Material No. 05-002) does not touch the internal surfaces of the spherical bearing (7).
(3)
Install spherical bearing (7) in the flap structure (8).
(4)
Apply LUBRICANTS (Material No. 06-008) to the thread of the locknut
(1) and the mating surfaces of the locknut (1) and the lockwasher (2).
(5)
Loosely install the lockwasher (2) and the locknut (1).
(6)
Apply SEALANTS (Material No. 09-002) to the mating face of the locking device (4).
(7)
Put the locking device (4) in position on the spherical bearing (7). If necessary, adjust the position of the spherical bearing (7) so that the locking device (4) engages correctly.
(8)
Install the washers (5) on the bolts (6).
(9)
Install the bolts (6), the washers (3) and the nuts (9).
(10)
TORQUE the nuts (9) to between 0.35 and 0.40 m.daN (30.97 and 35.39 lbf.in).
(11)
Apply SEALANTS (Material No. 09-002) to the parts that follow:
-
the bolts (6)
-
the washers (3) and (5)
-
the nuts (9).
(12)
Use the WRENCH - BEARING, FLAP TO CARRIAGE TRACK 2 (98D27507541000) to torque the locknut (1) to between 8.0 and 10.0 m.daN (58.99 and
73.74 lbf.ft).
(13)
Safety the locknut (1) with the lockwasher (2).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-52-21Page 412 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(65)
