-
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 575250-02
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific clamp No specific protective pad No specific safety barriers No specific warning notice No specific access platform 2.5 m (8 ft. 2 in.)
 1EFF : ALL 1 57-52-00Page 630 1 1 May 01/05R 1 1 1CES 1

 B. Consumable Materials

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 27-54-61-000-001 Removal of the Inboard Flap 27-54-61-400-001 Installation of the Inboard Flap 57-55-11-010-001 To Lower the Flap Track No. 2 Movable Fairing for
 Access 57-55-11-410-001 To Lift the Flap Track No. 2 Movable Fairing after
 Access NTM 57-52-50 PART 4 ASRM 575100 (for corrective action) 57-52-00-991-006 Fig. 606
 3. Job Set-up
__________
 Subtask 57-52-00-941-059
 A. Safety Precautions
 (1)
 Put warning notice in the cockpit to tell persons not to operate the flaps or slats.

 (2)
 Put the safety barriers in position.

 1EFF : ALL 1 57-52-00Page 631 1 1 May 01/04R 1 1 1CES 1

 Subtask 57-52-00-860-095

 B. Aircraft Maintenance Configuration
 (1)
 Extend the flaps fully (Ref. TASK 27-50-00-866-008).

 (2)
 Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control lever.

 (3)
 Put the access platform below the applicable wing trailing edge at flap track 2, zone 531(631).

 Subtask 57-52-00-865-066
 C. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
 Subtask 57-52-00-010-057
 D. Get Access R (1) Lower the flap track 2 movable fairing (Ref. TASK 57-55-11-010-001).
 (2)
 Disconnect the inboard flap from the flap track 2 carriage (Ref. TASK 27-54-61-000-001). Do not remove the end stop from the flap track.

 (3)
 Move the carriage along the flap track, until you can get clear access to the carriage forging.

R  (4) Use a clamp to hold the carriage in position on the flap track. Use a protective pad to prevent damage to the flap track surfaces.
 4. Procedure
_________ (Ref. Fig. 606/TASK 57-52-00-991-006) CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
 EDGE:

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.

 Flap Track 2 - Carriage Forging Figure 606/TASK 57-52-00-991-006
 1EFF : 1 1R 1CES  ALL  1 11 1 57-52-00 Page 633 May 01/04

 Subtask 57-52-00-110-058
 A. Preparation for Inspection
 (1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the carriage forging.
 (2) If applicable, clean the rear face of the carriage forging.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(20)