THE THICKNESS OF THE CHROME PLATE MUST BE 0.0030 INCH WIDTH OF THE SLOT
No. 4 and 5 Ground Spoiler Wear Limits Figure 601 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-12
 ALL  ú ú 01 Page 603 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 SPEED BRAKE FORWARD DRUM AND LEVER BRAKE - REMOVAL/INSTALLATION
_______________________________________________________________
 1.  General_______
 A.  There are two tasks in this procedure. There is a task for the removal and a task for the installation of the speed brake forward drum and the lever brake.
 TASK 27-62-21-004-001
 2.  Speed Brake Forward Drum and Lever Brake Removal________________________________________________
 A.  References
 (1)  
27-62-00/201, Speed Brake Control System

 B.  
Access

 (1)  
Location Zone
 101 Control Cabin - Left
 102 Control Cabin - Right
 202 Lower Nose Compartment

 (2)  
Access Panel
 1103 Forward Access Door
 3104 Forward Nose Wheel Well Panel

 C.
Prepare for the Speed Brake Forward Drum and the Lever Brake Removal

 S 864-002
 (1)  
Make sure the systems A and B hydraulic power is off (Ref 27-62-00/201).

 S 864-003

 (2)
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
P6-2 Panel
 1) AUTO SPEED BRAKE

 (3)  
Move the speed brake lever to the DOWN position.

 (4)  
Open the forward access door.

 S 014-006

 (5)
Remove the left forward access panel in the nose wheel well.

 D.  
Remove the Speed Brake Forward Drum and the Lever Brake

 S 864-004
 S 014-005
 S 034-007
 (1)  AIRPLANES WITH SPEED BRAKE LEVER POSITION SENSOR; Disconnect the adjustable control rod from the rod mounting bracket (Fig. 401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-21
 ALL  ú ú 01 Page 401 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 034-031
 (2)  AIRPLANES WITH SPEED BRAKE LEVER POSITION SENSOR; Remove the rod mounting bracket from the forward drum.
 S 034-009
 (3)  Disconnect the speed brake control cables SBA and SBB (Fig. 401): (a) Install cable clamps on the cables to keep a small tension on the cables.
 (b) (c) (d)  Disconnect the turnbuckles installed in the aft part of the lower nose compartment (Fig. 402).Install tags on the cables for identification.Remove the cable retainers and the cables from the speed brake forward drum (Fig./401).
 S 024-010
 (4)  Remove the forward drum (Fig. 401): (a) Remove the quadrant retaining bolt and washer. (b) Remove the forward drum from the shaft. 1) Hold the cam roller lever arm away from the forward drum.
 S 024-011
 (5)  Remove the lever brake assembly: (a) Disconnect the rod end for the speed brake lever actuator from the lever brake.
 (b)  Disconnect the lower control rod from the input arm for the lever brake.
 (c)  Remove the locknut that attaches the lever brake input arm to the shaft.
 (d)  Remove the bolts from the bearing retainers at each end of the lever brake shaft.
 (e)  Remove the lever brake from the airplane.
 NOTE:____ You can lower the shaft during the removal through the mounting slots in the bracket.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-21
 ALL  ú ú 01 Page 402 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 飛行操縱 FLIGHT CONTROLS 5(110)