position. 3) Make sure the SPEED BRAKE DO NOT ARM light is off. 4) Make sure the SPEED BRAKE ARMED light is on while the speed
 brake lever moves.
 (g)  Move the No. 1 thrust lever to the idle position.
 S 725-018
 (9)  
Do the RTO test again with the No. 2 thrust levers.

 S 865-009

 (10)
 Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P6-2 Panel 1) AUTO SLAT NO. 1 DC 2) AUTO SLAT NO. 2 DC 3) AIRPLANES WITH AUTOSLAT COMPUTER;

 AUTOSLAT NO. 1 AC AUTOSLAT NO. 2 AC
 S 865-010
 (11)
 Push the RECALL button on the glare shield.

 (a)  
Make sure the AUTOSLAT FAIL light on the P5-3 overhead panel is off.

 (b)  
If the light is on, do the autoslat failure troubleshooting (Ref 27-83-00/101).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-31
 ALL  ú ú 05 Page 505 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 D.  Put the Airplane Back to Its Usual Condition S 865-016
 (1)  
Move the speed brake lever to the DOWN position.
 S 865-011

 (2)  
Remove the systems A and B hydraulic power (Ref 27-62-00/201). S 865-012

 (3)  
Remove the electrical power (Ref 24-22-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-31
 ALL  ú ú 02 Page 506 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 SPEED BRAKE LEVER ACTUATOR - INSPECTION/CHECK
_____________________________________________
 1.  General_______
 A.  There is one task in this procedure, an inspection of the speed brake lever actuator. To do the inspection you measure the diameters of the bolts, bearing and bracket that attach the actuator to the structure.
 TASK 27-62-31-226-001
 2.  Speed Brake Lever Actuator Inspection_____________________________________
 A.  Standard Tools and Equipment
 (1)  
Micrometer 0 to 1 inch

 B.  
References

 (1)  
27-62-31/401, Speed Brake Lever Actuator

 C.  
Access

 (1)  
Location Zone
 202 Lower Nose Compartment

 D.  
Procedure

 S 026-002
 (1)
Remove the speed brake lever actuator (Ref 27-62-31/401).

 S 226-003

 (2)  
Examine the parts that attach the speed brake lever actuator for worn areas (Fig. 601).

 (a)  
Remove the parts.

 (b)  
Measure the diameters of the parts.

 (c)  
Compare the dimensions you measured with the permitted dimensions shown in Fig. 601.

 (d)  
Replace the parts that are not in the tolerance.

 (e)  
Install the parts.

 (3)
Install the speed brake lever actuator (Ref 27-62-31/401).

 S 426-004
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-31
 ALL  ú ú 01 Page 601 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500
MAINTENANCE MANUAL

SEE A
SPEED BRAKE CONTROL LEVER 
CABIN FLOOR CONTROL  ROD CONTROL LOWER  CHECKNUT 
A 
A 
BRAKE LEVER 
FWD  INBD SPEED BRAKE LEVER ACTUATOR BSEE 
A 
Speed Brake Lever Actuator Wear Limits Figure 601 (Sheet 1) 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(121)